Dual Smart Battery System Manager Features: SMBus Charger/Selector for Two Smart Batteries* Voltage and Current Accuracy within 0.2% of Value Reported by Battery Simplifies Construction of “Smart Battery System Manager” Includes All SMBus Charger V1.1 Safety Features Supports Autonomous Operation without a Host Allows Both Batteries to Discharge Simultaneously into Single Load with Low Loss (Ideal Diode) SMBus Switching for Dual Batteries with Alarm Monitoring for Charging Battery at All Times Pin Programmable Limits for Maximum Charge Current and Voltage Improve Safety Fast Autonomous Power Path™ Switching (<10µs) Low Loss Simultaneous Charging of Two Batteries >95% Efficient Synchronous Buck Charger AC Adapter Current Limiting* Maximizes Charge Rate SMBus Accelerator Improves SMBus Timing** Available in 48-Lead TSSOP Package

40MHz to 900MHz Quadrature Demodulator Features: RF Input Frequency Range: 40MHz to 900MHz High IIP3: 21dBm at 800MHz High IIP2: 58dBm at 800MHz I/Q Gain Mismatch: 0.3dB Max I/Q Phase Mismatch: 0.7° Noise Figure: 12.4dB at 800MHz Conversion Gain: 3.3dB at 800MHz Baseband Bandwidth: 130MHz Single Ended, 50 Matched 2XLO Input Shutdown Mode 16-Lead QFN (4mm × 4mm) Package with Exposed Pad

IC Multidisplay LED Controller Features: Step-Up/Direct-Connect Fractional Charge Pump Provides Up to 92% Efficiency Up to 400mA Continuous Output Current Independent Current and Dimming Control for 1-6 LED MAIN, 1-4 LED SUB and RGB LED Displays LED Currents Programmable Using 2-Wire I2C™ Serial Interface 1% LED Current Matching Low Noise Constant Frequency Operation* Minimal Component Count Automatic Soft-Start Limits Inrush Current 16 Exponentially Spaced Dimming States Provides 128:1 Brightness Range for MAIN and SUB Displays Up to 4096 Color Combinations for RGB Display Low Operating Current: IVIN = 180µA Tiny, Low Profile 24-Lead (4mm × 4mm × 0.75mm) QFN Package

>10 W (42 dBm), 2.7 GHz to 3.8 GHz, GaN Power Amplifier Features: High small signal gain: 34.5 dB typical High output power: 42 dBm typical at PIN = 18 dBm High PAE: 55% typical at PIN = 18 dBm Frequency range: 2.7 GHz to 3.8 GHz Supply voltage: VDD = 28 V at a quiescent current of 150 mA 5 mm × 5 mm, 32-lead LFCSP_CAV package

62V, 350mA Step-Down Regulator with 2.5A Quiescent Current and Integrated Diodes Features: Low Ripple Burst Mode® Operation 2.5μA IQ at 12VIN to 3.3VOUT Output Ripple < 5mVP-P Wide Input Voltage Range: 4.2V to 62V Operating Adjustable Switching Frequency: 200kHz to 2.2MHz Integrated Boost and Catch Diodes 350mA Output Current Fixed Output Voltages: 3.3V, 5V 2μA IQ at 12VIN Accurate Programmable Undervoltage Lockout FMEA Fault Tolerant (MSOP Package) Output Stays at or Below Regulation Voltage During Adjacent Pin Short or When a Pin is Left Floating Low Shutdown Current: IQ = 0.7μA Internal Sense Limits Catch Diode Current Power Good Flag Small, Thermally Enhanced 16-Pin MSOP and (3mm × 3mm) DFN Packages

Complete Isolated RS485/RS422 Module Transceiver + Power Features: RS485/RS422 Transceiver: 2500VRMS for 1 Minute UL-CSA Recognized File #E151738 CSA Component Acceptance Notice 5A Isolated DC Power: 5V at Up to 200mA No External Components Required 20Mbps or Low EMI 250kbps Data Rate High ESD: ±15kV HBM on Transceiver Interface High Common Mode Transient Immunity: 30kV/μs Integrated Selectable 120Ω Termination 3.3V (LTM2881-3) or 5.0V (LTM2881-5) Operation 1.62V to 5.5V Logic Supply Pin for Flexible Digital Interface Maximum Continuous Working Voltage: 560VPEAK High Input Impedance Failsafe RS485 Receiver Current Limited Drivers and Thermal Shutdown Compatible with TIA/EIA-485-A and PROFIBUS High Impedance Output During Internal Fault Condition Low Current Shutdown Mode (< 10μA) General Purpose CMOS Isolated Channel 15mm × 11.25mm BGA and LGA Packages

Low Noise Single-Ended to Differential Converter/ADC Driver Features: Rail-to-Rail Input and Outputs Fast Settling Time: 240ns, 0.01%, 8VP-P Output Step 1.9nV/√Hz Input-Referred Op Amp Noise High Impedance Input –3dB Bandwidth: 33MHz 2.7V to 12V Supply Operation No External Gain Resistors Required 4.8mA Supply Current Low Power Shutdown Low Distortion (HD2/HD3): –102dBc/–97dBc at 100kHz, VOUTDIFF = 4VP-P Low Offset Voltage: ±400μV Max High DC Linearity: <±1LSB, 16-Bit, 8VP-P Low Input Current Noise: 1.1pA/√Hz 3mm × 3mm 8-Pin DFN and 8-Lead MSOP Packages

Overvoltage, Undervoltage and Reverse Supply Protection Controller Features: Wide Operating Voltage Range: 2.5V to 34V Overvoltage Protection to 60V Reverse Supply Protection to –40V LTC4365: Blocks 50Hz and 60Hz AC Power LTC4365-1: Fast (1ms) Recovery from Fault No Input Capacitor or TVS Required for Most Applications Adjustable Undervoltage and Overvoltage Protection Range Charge Pump Enhances External N-Channel MOSFET Low Operating Current: 125μA Low Shutdown Current: 10μA Compact 8-Lead, 3mm × 2mm DFN and TSOT-23 (ThinSOT™) Packages AEC-Q100 Qualified for Automotive Applications

Ultralow Voltage Step-Up Converter and Power Manager Features: Operates from Inputs of 20mV Complete Energy Harvesting Power Management System Selectable VOUT of 2.5V, 3V, 3.7V or 4.5V LDO: 2.2V at 3mA Logic Controlled Output Reserve Energy Output Power Good Indicator Uses Compact Step-Up Transformers Small 12-Lead (3mm × 4mm) DFN or 16-Lead SSOP Packages

15V, 2.5A Synchronous Buck-Boost DC/DC Converter Features:Regulated Output with VIN Above, Below or Equal to VOUT2.7V to 15V Input Voltage Range2.5V to 14V Output Voltage Range2.5A Continuous Output Current: VIN ≥ 5V, VOUT = 5V, PWM ModeOutput Current MonitorUp to 95% Efficiency750kHz Switching Frequency, Synchronizable Between 300kHz and 1.5MHzInternal N-Channel MOSFETsSelectable Burst Mode® Operation, IQ = 50μAShutdown Current < 1μAOvervoltage ProtectionOutput Disconnect in ShutdownInternal Soft-StartSmall, Thermally Enhanced 16-Lead (4mm × 5mm × 0.75mm) DFN and 20-Lead TSSOP Package