Precision Analog Microcontroller, Tunable Optical Control Microcontroller Features: Analog input/output 22-channel, 14-bit, 800 kSPS analog-to-digital converter (ADC) 10 external channels 1 on-chip die temperature monitor 6 current output digital-to-analog converter (IDAC) monitor channels 3 power monitor channels 2 buffered reference output channels Fully differential and single-ended modes 0 V to 2.5 V analog input range 6 low noise, 12-/14-bit IDAC outputs 1× 250 mA, 1× 200 mA, 2× 100 mA, and 2× 20 mA Semiconductor optical amplifier (SOA) IDAC pull-down to −3.0 V for fast current sink Eight 12-bit voltage output DACs (VDACs) Channel 0 and Channel 1: 0 V to 3 V, 75 Ω load Channel 2 and Channel 3: −5 V to 0 V, 500 Ω load Channel 4 and Channel 5: 0 V to 3 V, 300 Ω load Channel 6: 0 V to 5 V, 500 Ω load Channel 7: 0 V to 5 V, 100 Ω load 2.5 V, on-chip voltage reference 2 buffered 2.5 V outputs Microcontroller ARM Cortex-M3 processor, 32-bit RISC architecture Serial wire port supports code download and debugging Clocking options Trimmed on-chip oscillator (±3%) 80 MHz phase-locked loop (PLL) External 16 MHz crystal option External clock source Memory 2× 128 kB Flash/EE memories, 32 kB SRAM In-circuit download, SW-DP-based debugging Software triggered in-circuit reprogrammability On-chip peripherals UART, 2× I2C and 2× SPI serial input/output 28-pin general-purpose input/output (GPIO) port 3 general-purpose timers Wake-up (W/U) timer Watchdog timer (WDT) 32-element programmable logic array (PLA) Vectored interrupt controller Interrupt on edge or level external pin inputs 9× external interrupts Power Multiple supplies 5 V for VDAC6 and VDAC7 3.3 V for digital and analog inputs/outputs 1.8 V to 2.7 V for IDACs −5 V supply for IDAC3 and VDAC2/VDAC3 Package and temperature range 6 mm × 6 mm, 112-ball CSP_BGA package Fully specified for −40°C to +85°C ambient operation Tools QuickStart™ development system Full third party support

Precision Analog Microcontroller, 16-Bit Analog Input/Output with MDIO Interface, Arm Cortex-M33 Features: Analog input/output Multichannel, 16-bit, 2 MSPS ADC Up to 16 external channels On-chip die temperature monitor 4 power monitor channels 4 PGA/TIA channels supporting voltage and current measurements Fully differential and single-ended modes 0 V to VREF analog input range 12-bit voltage output DACs 8× 0 V to 2.5 V, 1 kΩ load 4× 0 V to 2.5 V, 2.5 kΩ load On-chip low drift voltage reference, 1.25 V or 2.5 V Buffered 1.25 V or 2.5 V output 4 voltage comparators Microcontroller 32-bit Arm Cortex-M33 core, 32-bit RISC architecture, FPU Serial wire port supports code download and debug Clocking options 16 MHz on-chip oscillator 160 MHz PLL output with programmable divider External clock source Memory 2× 512 kB independent Flash/EE memories 10,000-cycle Flash/EE endurance 20-year Flash/EE retention 128 kB SRAM with ECC Software triggered, in circuit reprogrammability via MDIO or I2C On-chip peripherals 2× UART, 3× SPI, 3× I2C serial input/output Multilevel voltage (3.3 V, 1.8 V, 1.2 V) GPIOs MDIO slave up to 10 MHz 5 general-purpose timers Wake-up timer (WUTs) Watchdog timers (WDTs) 32-element PLA 16-bit PWM 10 external Interrupts Power Multiple supplies: 3.3 V for voltage DACs and ADCs, and 3.3 V, 1.8 V, or 1.2 V for digital inputs/outputs Flexible operating modes for low power applications Packages and temperature range 5 mm × 5 mm 81-ball CSP_BGA and 3.46 mm × 3.46 mm 64-ball WLCSP BGA package uses ULA molding compounds Fully specified for −40°C to +105°C operation Tools Low cost quick start development system Full third-party support  

40W SPDT Failsafe Switch SMT, 0.1 - 2.1 GHz Features: High Input P0.1dB: +46 dBm Tx Low Insertion Loss: 0.4 dB High IIP3: +74 dBm Single Positive Control: 0/ +3V to 0/ +8V Failsafe Operation; Tx 'On' when Unpowered 2 × 2mm DFN SMT Package

Single Channel, 256-Position, I2C / SPI, Nonvolatile Digital Potentiometer Features: 10 kΩ and 100 kΩ resistance options Resistor tolerance: 8% maximum Wiper current: ±6 mA Low temperature coefficient: 35 ppm/°C Wide bandwidth: 3 MHz Fast start-up time < 75 μs Linear gain setting mode Single- and dual-supply operation Independent logic supply: 1.8 V to 5.5 V Wide operating temperature: −40°C to +125°C 3 mm × 3 mm LFCSP Qualified for automotive applications

High Bandwidth 12-Bit Parallel Interface Multiplying D/A Converter Features: 2.5 V to 5.5 V supply operation Fast parallel interface (17 ns write cycle) Update rate of 20.4 MSPS INL of ±1 LSB for 12-bit DAC ±10 V reference input 10 MHz multiplying bandwidth Extended temperature range: –40°C to +125°C See data sheet for additional features

Quad, 16-Bit nanoDAC with 5ppm/C On-Chip Reference Features: Low power, smallest pin-compatible, quad nanoDACs  AD5664R: 16 bits AD5644R: 14 bits AD5624R: 12 bits User selectable external or internal reference External reference default On-chip 1.25 V/2.5 V, 5 ppm/°C reference 10-lead MSOP; 10-lead, 3 mm × 3 mm LFCSP_WD; and 12-ball, 1.665 mm × 2.245 mm WLCSP 2.7 V to 5.5 V power supply Guaranteed monotonic by design Power-on reset to zero scale Per channel power-down Serial interface, up to 50 MHz

High Precision, Impedance & Electrochemical Front End Features: Analog input 16-bit ADC with both 800 kSPS and 1.6 MSPS options Voltage, current, and impedance measurement capability Internal and external current and voltage channels Ultralow leakage switch matrix and input mux Input buffers and programmable gain amplifier Voltage DACs Dual output voltage DAC with an output range of 0.2 V to 2.4 V 12-bit VBIAS0 output to bias potentiostat 6-bit VZERO0 output to bias TIA Ultra low power: 1 µA 1 high speed, 12-bit DAC Output range to sensor: ±607 mV Programmable gain amplifier on output with gain settings of 2 and 0.05 Amplifiers, accelerators, and references 1 low power, low noise potentiostat amplifier suitable for potentiostat bias in electrochemical sensing 1 low noise, low power TIA, suitable for measuring sensor current output 50 pA to 3 mA range Programmable load and gain resistors for sensor output Analog hardware accelerators Digital waveform generator Receive filters Complex impedance measurement (DFT) engine 1 high speed TIA to handle wide bandwidth input signals from 0.015 Hz up to 200 kHz Digital waveform generator for generation of sinusoid and trapezoid waveforms 2.5 V and 1.82 V internal reference voltage sources System level power savings Fast power-up and power-down analog blocks for duty cycling Programmable AFE sequencer to minimize workload of host controller 6 kB SRAM to preprogram AFE sequences Ultra low power potentiostat channel: 6.5 µAof current consumption when powered on and all other blocks in hibernate mode Smart sensor synchronization and data collection Cycle accurate control of sensor measurement Sequencer controlled GPIOs On-chip peripherals SPI serial input/output Wake-up timer Interrupt controller Power 2.8 V to 3.6 V supply 1.82 V input/output compliant Power-on reset Hibernate mode with low power DAC and potentiostat amplifier powered up to maintain sensor bias Package and temperature range 3.6 mm × 4.2 mm, 56-ball WLCSP 7 mm × 7 mm, 48-lead LFCSP Fully specified for operating temperature range of −40°C to +85°C AD5940 and AD5941 fully specified for operating temperature range of −40°C to +85°C AD5941W fully specified for operating temperature range of −40°C to +105°C AEC-Q100 qualified for automotive applications

4-Channel, Low Noise, Low Power, 24-Bit, Sigma-Delta ADC with PGA and Reference Features: Three power modes RMS noise Low power: 24 nV rms at 1.17 SPS, gain = 128 (255 μA typical) Mid power: 20 nV rms at 2.34 SPS, gain = 128 (355 μA typical) Full power: 23 nV rms at 9.4 SPS, gain = 128 (930 μA typical) Up to 22 noise free bits in all power modes (gain = 1) Output data rate Full power: 9.38 SPS to 19,200 SPS Mid power: 2.34 SPS to 4800 SPS Low power: 1.17 SPS to 2400 SPS Rail-to-rail analog inputs for gains > 1 Simultaneous 50 Hz/60 Hz rejection at 25 SPS (single cycle settling) Diagnostic functions (which aid safe integrity level (SIL) certification Crosspoint multiplexed analog inputs 4 differential/7 pseudo differential inputs Programmable gain (1 to 128) Band gap reference with 10 ppm/°C drift maximum (70 μA) Matched programmable excitation currents Internal clock oscillator On-chip bias voltage generator Low-side power switch General-purpose outputs Multiple filter options Internal temperature sensor Self and system calibration Sensor burnout detection Automatic channel sequencer Per channel configuration Power supply: 2.7 V to 3.6 V and ±1.8 V Independent interface power supply Power-down current: 5 μA maximum Temperature range: −40°C to +125°C 32-lead LFCSP/24-lead TSSOP 3-wire or 4-wire serial interface SPI, QSPI, MICROWIRE, and DSP compatible Schmitt trigger on SCLK ESD: 4 kVAD7124-4-EP Supports defense and aerospace applications (AQEC standard) Download AD7124-4-EP Data Sheet (PDF) Full military temperature range: −55°C to +125°C Controlled manufacturing baseline 1 assembly/test site 1 fabrication site Product change notification Qualification data available on request V62/19614

Lithium Ion Battery Monitoring System Features: 12-bit ADC, 1 μs per channel conversion time 6 analog input channels,  CM range 0.5 V to 27.5 V 6 auxiliary ADC Inputs ±1.6 mV cell voltage accuracy On-chip voltage regulator Cell balancing interface Daisy-chain interface Internal reference: ±3 ppm/°C 1.8 μA power-down current High input impedance Serial interface with alert function See data sheet for additional features

True Bipolar Input, Dual 14-Bit, 2-Channel, Simultaneous Sampling SAR ADC Features: Dual 12-bit/14-bit, 2-channel ADC True bipolar analog inputs Programmable input ranges:  ±10 V, ±5 V, 0 V to 10 V  ±12 V with 3 V external reference Throughput rate: 1 MSPS Simultaneous conversion with read in less than 1 μs Low current consumption:  8.3 mA typical in normal mode  320 nA typical in shutdown mode AD7366  72 dB SNR at 50 kHz input frequency  12-bit no missing codes AD7367  76 dB SNR at 50 kHz input frequency  14-bit no missing codes Accurate on-chip reference: 2.5 V ± 0.2% −40°C to +85°C operation High speed serial interface Compatible with SPI®, QSPI™, MICROWIRE™, and DSP High analog input impedance