High Precision, Impedance & Electrochemical Front End Features: Analog input 16-bit ADC with both 800 kSPS and 1.6 MSPS options Voltage, current, and impedance measurement capability Internal and external current and voltage channels Ultralow leakage switch matrix and input mux Input buffers and programmable gain amplifier Voltage DACs Dual output voltage DAC with an output range of 0.2 V to 2.4 V 12-bit VBIAS0 output to bias potentiostat 6-bit VZERO0 output to bias TIA Ultra low power: 1 µA 1 high speed, 12-bit DAC Output range to sensor: ±607 mV Programmable gain amplifier on output with gain settings of 2 and 0.05 Amplifiers, accelerators, and references 1 low power, low noise potentiostat amplifier suitable for potentiostat bias in electrochemical sensing 1 low noise, low power TIA, suitable for measuring sensor current output 50 pA to 3 mA range Programmable load and gain resistors for sensor output Analog hardware accelerators Digital waveform generator Receive filters Complex impedance measurement (DFT) engine 1 high speed TIA to handle wide bandwidth input signals from 0.015 Hz up to 200 kHz Digital waveform generator for generation of sinusoid and trapezoid waveforms 2.5 V and 1.82 V internal reference voltage sources System level power savings Fast power-up and power-down analog blocks for duty cycling Programmable AFE sequencer to minimize workload of host controller 6 kB SRAM to preprogram AFE sequences Ultra low power potentiostat channel: 6.5 µAof current consumption when powered on and all other blocks in hibernate mode Smart sensor synchronization and data collection Cycle accurate control of sensor measurement Sequencer controlled GPIOs On-chip peripherals SPI serial input/output Wake-up timer Interrupt controller Power 2.8 V to 3.6 V supply 1.82 V input/output compliant Power-on reset Hibernate mode with low power DAC and potentiostat amplifier powered up to maintain sensor bias Package and temperature range 3.6 mm × 4.2 mm, 56-ball WLCSP 7 mm × 7 mm, 48-lead LFCSP Fully specified for operating temperature range of −40°C to +85°C AD5940 and AD5941 fully specified for operating temperature range of −40°C to +85°C AD5941W fully specified for operating temperature range of −40°C to +105°C AEC-Q100 qualified for automotive applications

SPI, 1.5 RON, 15 V/5 V/+12 V, High Density Octal SPST Switch Features: SPI with error detection Includes CRC, invalid read and write address, and SCLK count error detection Supports burst mode and daisy-chain mode Industry-standard SPI Mode 0 and Mode 3 interface compatible Integrated passive components Route through of digital signals and supplies Guaranteed break-before-make switching allowing external wiring of switches to deliver multiplexer configurations 1.5 typical on resistance at 25°C (±15 V dual supply) 0.3 typical on resistance flatness at 25°C (±15 V dual supply) 0.1 typical on resistance match between channels at 25°C (±15 V dual supply) VSS to VDD analog signal range Fully specified at ±15 V, ±5 V, and +12 V 1.8 V logic compatibility with 2.7 V ≤ VL ≤ 3.3 V (excludes SPI readback to a 1.8 V device) 4 mm × 5 mm, 30-terminal LGA 

Robust, Industrial, Low Power 10BASE-T1L Ethernet MAC-PHY Features: 10BASE-T1L IEEE Standard 802.3cg-2019 compliant Integrated MAC with SPI interface SPI supporting 10 Mbps full duplex Supports OPEN Alliance 10BASE-T1x MAC-PHY serial interface Low power consumption: dual supply 42 mW typical Supports 1.0 V p-p and 2.4 V p-p transmit levels Autonegotiation capability Supports intrinsic safety applications External termination resistors Separate receive and transmit pins MDIO memory map accessible via SPI On Chip FIFOs: 20kB receive, 8kB transmit (configurable) Cut-through or Store and forward operation Rx high and low priority queues IEEE 1588 timestamp support Statistics counters 16 MAC addresses supported for frame filtering Link LED Unmanaged configuration using pin strapping including: Master/Slave selection Transmit amplitude 25 MHz crystal oscillator/25 MHz external clock input Single supply 1.8 V/3.3 V operation (mode dependent) Cable Reach 1700 meters with 1.0 V p-p 1700 meters with 2.4 V p-p EMC test standards IEC 61000-4-4 electrical fast transient (EFT) (±4 kV) IEC 61000-4-2 ESD (±4 kV contact discharge) IEC 61000-4-2 ESD (±8 kV air discharge) IEC 61000-4-6 conducted immunity (10V/m) IEC 61000-4-5 surge (±4kV) IEC 61000-4-3 radiated immunity (Class A) EN55032 radiated emissions (Class B) Small package 40-lead (6 mm × 6 mm) LFCSP Wide temperature range -40°C to 105°C

Robust, Industrial, Low Power 10BASE-T1L Ethernet MAC-PHY Features: 10BASE-T1L IEEE Standard 802.3cg-2019 compliant Integrated MAC with SPI interface SPI supporting 10 Mbps full duplex Supports OPEN Alliance 10BASE-T1x MAC-PHY serial interface Low power consumption: dual supply 42 mW typical Supports 1.0 V p-p and 2.4 V p-p transmit levels Autonegotiation capability Supports intrinsic safety applications External termination resistors Separate receive and transmit pins MDIO memory map accessible via SPI On Chip FIFOs: 20kB receive, 8kB transmit (configurable) Cut-through or Store and forward operation Rx high and low priority queues IEEE 1588 timestamp support Statistics counters 16 MAC addresses supported for frame filtering Link LED Unmanaged configuration using pin strapping including: Master/Slave selection Transmit amplitude 25 MHz crystal oscillator/25 MHz external clock input Single supply 1.8 V/3.3 V operation (mode dependent) Cable Reach 1700 meters with 1.0 V p-p 1700 meters with 2.4 V p-p EMC test standards IEC 61000-4-4 electrical fast transient (EFT) (±4 kV) IEC 61000-4-2 ESD (±4 kV contact discharge) IEC 61000-4-2 ESD (±8 kV air discharge) IEC 61000-4-6 conducted immunity (10V/m) IEC 61000-4-5 surge (±4kV) IEC 61000-4-3 radiated immunity (Class A) EN55032 radiated emissions (Class B) Small package 40-lead (6 mm × 6 mm) LFCSP Wide temperature range -40°C to 105°C

Low Complexity, 2-Port Ethernet Switch with Integrated 10BASE-T1L PHYs Features: 10BASE-T1L IEEE® Std 802.3cg-2019™ compliant Supports 1.0 V p-p & 2.4 V p-p transmit Levels Cable reach Up to 1700 meters with 1.0 V p-p transmit level Up to 1700 meters with 2.4 V p-p transmit level Low power consumption Low power consumption - single supply 80 mW typ Dual supply 1.0 V p-p: 77 mW typical Integrated switch with SPI interface 10 Mbps full duplex 16 MAC addresses supported for frame forwarding Supports OPEN Alliance 10BASE-T1x MACPHY SPI MDIO memory map accessible via SPI Supports high & low priority queues Total buffer memory of 28 kB shared between ports and host Autonegotiation capability Managed or unmanaged configuration Cut through or store and forward operation IEEE 1588 time stamp capture on transmit and receive Diagnostics Frame generator and checker Multiple loopback modes IEEE test mode support Port dedicated statistics counters Link and cable diagnostics 25 MHz crystal or external clock input Single or dual supply with 1.8 V or 3.3 V operation Integrated power supply monitoring and POR Small package: 48-lead, 7 mm × 7 mm LFCSP Temperature range Industrial: 40°C to +85°C Extended: 40°C to +105°C

Precision MEMS IMU Module Features: Triaxial, digital gyroscope  ±125°/sec, ±500°/sec, ±2000°/sec dynamic range models 2°/hr in-run bias stability (ADIS16465-1)  0.15°/√hr angular random walk (ADIS16465-1 and ADIS16465-2)  ±0.05° axis to axis misalignment error  Triaxial, digital accelerometer, ±8 g 3.6 μg in-run bias stability Triaxial, delta angle, and delta velocity outputs Factory calibrated sensitivity, bias, and axial alignment Calibration temperature range: −40°C to +85°C   SPI-compatible data communications Programmable operation and control  Automatic and manual bias correction controls Data ready indicator for synchronous data acquisition External sync modes: direct, pulse, scaled, and output On demand self test of inertial sensors On demand self test of flash memory Single-supply operation (VDD): 3.0 V to 3.6 V 2000 g mechanical shock survivability Operating temperature range: −40°C to +105°C

Precision, Miniature MEMS IMU Features: Triaxial, digital gyroscope ±125°/sec, ±500°/sec, ±2000°/sec dynamic range models 2.3°/hr in-run bias stability (ADIS16507-1) 0.13°/√hr angular random walk, x-axis and y-axis, 1 σ (ADIS16507-1) ±0.25° axis to axis misalignment error Triaxial, digital accelerometer, ±392 m/sec2 dynamic range 125 μm/sec2 in-run bias stability, x-axis and y-axis, 1 σ Triaxial, delta angle and delta velocity outputs Factory calibrated sensitivity, bias, and axial alignment Calibration temperature range: −40°C to +85°C SPI compatible data communications Programmable operation and control Automatic and manual bias correction controls Data ready indicator for synchronous data acquisition External sync modes: direct, scaled, and output On demand self-test of inertial sensors On demand self-test of flash memory Single-supply operation (VDD): 3.0 V to 3.6 V 19,600 m/sec2 mechanical shock survivability Operating temperature range: −40°C to +105°C

Precision, Miniature MEMS IMU

Features:

• Triaxial, digital gyroscop
  • ±125°/sec, ±500°/sec, ±2000°/sec dynamic range models
  • 2.3°/hr in-run bias stability (ADIS16507-1)
  • 0.13°/√hr angular random walk, x-axis and y-axis, 1 σ (ADIS16507-1)
  • ±0.25° axis to axis misalignment error
• Triaxial, digital accelerometer, ±392 m/sec2 dynamic range
  • 125 μm/sec2 in-run bias stability, x-axis and y-axis, 1 σ
• Triaxial, delta angle and delta velocity outputs
• Factory calibrated sensitivity, bias, and axial alignment
  • Calibration temperature range: −40°C to +85°C
• SPI compatible data communications
• Programmable operation and control
  • Automatic and manual bias correction controls
  • Data ready indicator for synchronous data acquisition
  • External sync modes: direct, scaled, and output
  • On demand self-test of inertial sensors
  • On demand self-test of flash memory
• Single-supply operation (VDD): 3.0 V to 3.6 V
• 19,600 m/sec2 mechanical shock survivability
• Operating temperature range: −40°C to +105°C

Applications:

• Navigation, stabilization, and instrumentation
• Unmanned and autonomous vehicles
• Smart agriculture and construction machinery
• Factory/industrial automation, robotics
• Virtual/augmented reality
• Internet of Moving Things

GaAs, pHEMT, Low Noise Amplifier, 20 GHz to 54 GHz Features: Gain: 21.5 dB typical at 30 GHz to 44 GHz Input return loss: 22 dB typical at 30 GHz to 44 GHz Output return loss: 23 dB typical at 30 GHz to 44 GHz OP1dB: 14 dB typical at 30 GHz to 44 GHz PSAT: 18 dBm typical at 30 GHz to 44 GHz OIP3: 21.5 dBm typical at 30 GHz to 44 GHz Noise figure: 3.0 dB typical at 30 GHz to 44 GHz 3 V supply voltage at 120 mA 50 Ω matched input and output Die size: 2.3 mm x 1.45 mm x 0.1 mm

2 GHz to 28 GHz, GaAs, pHEMT, MMIC Low Noise Amplifier Features: P1dB: 20 dBm typical at 2 GHz to 6 GHz PSAT: 20.5 dBm typical at 2 GHz to 6 GHz Gain: 15.5 dB typical at 6 GHz to 28 GHz Noise figure: 2.5 dB typical at 2 GHz to 20 GHz OIP3: 26 dBm typical at 2 GHz to 6 GHz Supply voltage: 5 V at 53 mA 50 Ω matched input and output ADL9006CHIPS P1dB: 19 dBm typical at 2 GHz to 14 GHz Gain: 15.5 dB typical at 14 GHz to 22 GHz Noise figure: 2.2 dB at 2 GHz to 14 GHz Output IP3: 24 dBm typical at 2 GHz to 14 GHz Power supply voltage: 5 V with a 55 mA total supply current 50 Ω matched input and output