18-Bit, 15 MSPS, Module Data Acquisition Solution Features: Integrated fully differential ADC driver with signal scaling Wide input common-mode voltage range High common-mode rejection Single-ended to differential conversion Pin selectable input range with overrange Input ranges with 4.096 V REFBUF: ±10 V, ±5 V, ±4.096 V, ±2.5 V, and ±1.5 V Gain/attenuation options: 0.37, 0.73, 0.87, 1.38, and 2.25 Critical passive components 0.005% precision matched resistor array for FDA 9 mm × 9 mm, 0.8 mm pitch, 100-ball CSP_BGA package 2.5× footprint reduction vs. discrete solution Low power, dynamic power scaling, power-down mode 143 mW typical at 15 MSPS Throughput: 15 MSPS, no pipeline delay INL error: ±3.1 ppm typical, ±6.2 ppm maximum (Gain = 0.73, gain = 0.87, gain = 1.38, gain = 2.25) SINAD: 90.4 dB typical at 20 kHz (gain = 0.73) THD: −117 dB at 1 kHz, −110 dB at 100 kHz (gain = 0.73) Gain error: ±0.005%FS typical Gain error drift: ±0.13 ppm/°C typical On-board reference buffer with VCMO generation Serial LVDS interface Wide operating temperature range: −40°C to +85°C

Ultrafast SiGe Voltage Comparator (Featuring Reduced Swing PECL Output Drivers) Features: 180 ps propagation delay 25 ps overdrive and slew rate dispersion 8 GHz equivalent input rise time bandwidth 100 ps minimum pulse width 37 ps typical output rise/fall 10 ps deterministic jitter (DJ) 200 fs random jitter (RJ) −2 V to +3 V input range with +5 V/−5 V supplies On-chip terminations at both input pins Resistor-programmable hysteresis Differential latch control Power supply rejection > 70 dB

Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter Features: Single-chip, low power UHF transmitter 75 MHz to 1 GHz frequency operation Multichannel operation using fractional-N PLL 2.3 V to 3.6 V operation On-board regulator Programmable output power −16 dBm to +14 dBm, 0.4 dB steps Data rates: dc to 179.2 kbps Low current consumption 868 MHz, 10 dBm, 21 mA 433 MHz, 10 dBm, 17 mA 315 MHz, 0 dBm, 10 mA Programmable low battery voltage indicator 24-lead TSSOP

I2C CMOS 8 10 Unbuffered Analog Switch Array with Dual/Single Supplies Features: I2C-compatible Interface 3.4 MHz High Speed I2C Option 32-lead LFCSP_VQ (5 mm × 5 mm) Double-buffered Input Logic Simultaneous Update of Multiple Switches Up to 300 MHz Bandwidth Fully Specified at Dual ±5 V/single +12 V Operation On Resistance 35 Ω Maximum Low Quiescent Current < 20 μA

SPI Interface, 1.5 RON, 15 V/+12 V, Quad SPST Switch, Mux Configurable Features: SPI interface with error detection Includes CRC, invalid read/write address, and SCLK count error detection Supports burst mode and daisy-chain mode Industry-standard SPI Mode 0 and Mode 3 interface compatible Guaranteed break-before-make switching allowing external wiring of switches to deliver multiplexer configurations 1.5 typical on resistance at 25°C 0.3 typical on resistance flatness at 25°C 0.1 typical on resistance match between channels at 25°C VSS to VDD analog signal range Fully specified at ±15 V, ±5 V, and +12 V 1.8 V logic compatibility with 2.7 V ≤ VL ≤ 3.3 V 24-lead LFCSP

24 V to 220 V Precision Operational Amplifier Features: Wide range of operating voltages Dual-supply: ±12 V to ±110 V Asymmetrical supply operation: 24 V to 220 V Wide input common-mode voltage range: 3 V from rails High common-mode rejection ratio: 160 dB typical High AOL: 170 dB typical High slew rate 74 V/μs typical 24 V/μs typical with external input clamping diodes Low input bias current: 2 pA maximum Low input offset voltage: 1 mV maximum Low input offset voltage drift: 2 μV/°C maximum Low input voltage noise: 8 nV/√Hz typical at 10 kHz Wide small signal bandwidth: 10 MHz typical Resistor adjustable quiescent current: 0.6 mA to 3 mA (VS = ±110 V) Unity-gain stable Thermal monitoring Small footprint: 12-lead, 7 mm × 7 mm LFCSP compliant with IEC 61010-1 spacing Shutdown mode

Quad Voltage Monitor and Sequencer Features: Powered from 2.7 V to 5.5 V on the VCC pin Logical core with internal timeouts provides power supply sequencing and fault protection 4 inputs can be programmed to monitor different voltage levels with resistor dividers Monitors 4 supplies via 0.8% accurate comparators 3 open-drain enable outputs Open-drain power-good output (PWRGD) 10-lead MSOP

5 kV Signal Isolated, High Speed (16 Mbps), ESD Protected, Full/Half Duplex RS-485 Transceiver Features: Isolated, RS-485/RS-422 transceiver, configurable as half- or full-duplex ±8 kV ESD protection on RS-485 input/output pins 16 Mbps data rate Complies with ANSI TIA/EIA RS-485-A-1998 and ISO 8482: 1987(E) Suitable for 5 V or 3.3 V operation (VDD1) High common-mode transient immunity: >25 kV/µs Receiver has open-circuit, fail-safe design 32 nodes on the bus Thermal shutdown protection Safety and regulatory approvals UL recognition: 5000 V rms isolation voltage for 1 minute, per UL 1577 VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 Reinforced insulation, VIORM = 849 V peak See data sheet for additional features

2.5 kV Signal and Power Isolated, 15 kV ESD Protected, Full/Half Duplex RS-485 Transceiver (500kbps) Features: Isolated RS-485/RS-422 transceiver, configurable as half or full duplex isoPower integrated isolated dc-to-dc converter ±15 kV ESD protection on RS-485 input/output pins ADM2582E data rate: 16 Mbps ADM2587E data rate: 500 kbps 5 V or 3.3 V operation See datasheet for additional features

Robust 5 kV RMS Isolated RS-485/RS-422 Transceiver with Level 4 EMC and Full 42 V Protection Features: 5 kV rms isolated RS-485/RS-422 transceiver ±42 V ac/dc peak fault protection on RS-485 bus pins Certified Level 4 EMC protection on RS-485 A, B bus pins IEC 61000-4-5 surge protection (±4 kV) IEC 61000-4-4 electrical fast transient (EFT) protection (±2 kV) IEC 61000-4-2 electrostatic discharge (ESD) protection ±8 kV contact discharge ±15 kV air discharge IEC 61000-4-6 conducted radio frequency (RF) immunity (10 V/m rms) Certified IEC 61000-4-x immunity across isolation barrier IEC 61000-4-2 ESD, IEC 61000-4-4 EFT, IEC 61000-4-5 surge, IEC 61000-4-6 conducted RF immunity, IEC 61000-4-3 radiated immunity, IEC 61000-4-8 magnetic immunity RS-485 A, B pins human body model (HBM) ESD protection: >±30 kV Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-10, UL 1577, CQC11-471543-2012 TIA/EIA RS-485/RS-422 compliant over full supply range 3 V to 5.5 V operating voltage range on VDD2 1.7 V to 5.5 V operating voltage range on VDD1 logic supply Common-mode input range of −25 V to +25 V High common-mode transient immunity: >75 kV/μs Robust noise immunity (tested to the IEC 62132-4 standard) Passes EN55022 Class B radiated emissions by 6 dBμV/m margin Receiver short-circuit, open-circuit, and floating input fail-safe Supports 256 bus nodes (96 kΩ receiver input impedance) −40°C to +125°C temperature option Glitch free power-up/power-down (hot swap)ADM2795E-EP supports defense and aerospace applications (AQEC standard) Download ADM2795E-EP data sheet (pdf) Military −55°C to +125°C temperature range Controlled manufacturing baseline 1 assembly/test site Enhanced product change notification Qualification data available on request V62/17611 DSCC Drawing Number