The AD7147 CapTouch™ controller is designed for use with capacitance sensors implementing functions such as buttons, scroll bars, and wheels. The sensors need only one PCB layer, enabling ultrathin applications.The AD7147 is an integrated CDC with on-chip environmental calibration. The CDC has 13 inputs channeled through a switch matrix to a 16-bit, 250 kHz sigma-delta (Σ-Δ) converter. The CDC is capable of sensing changes in the capacitance of the external sensors and uses this information to register a sensor activation. By programming the registers, the user has full control over the CDC setup.High resolution sensors require minor software to run on the host processor.The AD7147 is designed for single electrode capacitance sensors (grounded sensors). There is an active shield output to minimize noise pickup in the sensor.The AD7147 has on-chip calibration logic to compensate for changes in the ambient environment. The calibration sequence is performed automatically and at continuous intervals as long as the sensors are not touched. This ensures that there are no false or non-registering touches on the external sensors due to a changing environment.The AD7147 has an SPI-compatible serial interface, and the AD7147-1 has an I2C®-compatible serial interface. Both parts have an interrupt output, as well as a GPIO. There is a VDRIVE pin to set the voltage level for the serial interface independent of VCC.The AD7147 is available in a 24-lead, 4 mm × 4 mm LFCSP and operates from a 2.6 V to 3.6 V supply. The operating current consumption in low power mode is typically 26 μA for 13 sensors.APPLICATIONS Cell phones Personal music and multimedia players Smart handheld devices Television, A/V, and remote controls Gaming consoles Digital still cameras 

The AD9911 is a complete direct digital synthesizer (DDS).This device includes a high speed DAC with excellent widebandand narrowband spurious-free dynamic range (SFDR) as well asthree auxiliary DDS cores without assigned digital-to-analogconverters (DACs). These auxiliary channels are used for spurreduction, multitone generation, or test-tone modulation.The AD9911 is the first DDS to incorporate SpurKillertechnology and multitone generation capability. Multitonemode enables the generation up to four concurrent carriers;frequency, phase and amplitude can be independentlyprogrammed. Multitone generation can be used for systemtests, such as inter-modulation distortion and receiver blockersensitivity. SpurKilling enables customers to improve SFDRperformance by reducing the magnitude of harmoniccomponents and/or the aliases of those harmonic components.Test-tone modulation efficiently enables sine wave modulationof amplitude on the output signal using one of the auxiliaryDDS cores.The AD9911 can perform modulation of frequency, phase, oramplitude (FSK, PSK, ASK). Modulation is implemented bystoring profiles in the register bank and applying data to theprofile pins. In addition, the AD9911 supports linear sweep offrequency, phase, or amplitude for applications such as radarand instrumentation.The DDS acts as a high resolution frequency divider with theREF_CLK as the input and the DAC providing the output. TheREF_CLK input can be driven directly or used in combinationwith an integrated REF_CLK multiplier (PLL). The REF_CLKinput also features an oscillator circuit to support an externalcrystal as the REF_CLK source. The crystal can be used incombination with the REF_CLK multiplier.The AD9911 I/O port offers multiple configurations to providesignificant flexibility. The I/O port offers an SPI-compatiblemode of operation that is virtually identical to the SPI operationfound in earlier Analog Devices DDS products.Flexibility is provided by four data pins (Pin SDIO_0,Pin SDIO_1, Pin SDIO_2, and Pin SDIO_3) that allow fourprogrammable modes of I/O operation.The DAC output is supply referenced and must be terminatedinto AVDD by a resistor and an AVDD center-tapped transformer.The DAC has its own programmable reference to enabledifferent full-scale currents.The DDS core (the AVDD pins and the DVDD pins) is poweredby a 1.8 V supply. The digital I/O interface (SPI) operates at3.3 V and requires that the Pin DVDD_I/O (Pin 49) beconnected to 3.3 V. Applications Agile local oscillator Test and measurement equipment Commercial and amateur radio exciter Radar and sonar Test-tone generation Fast frequency hopping Clock generation

The AD9954 is a direct digital synthesizer (DDS) that uses advanced technology, coupled with an internal high speed, high performance DAC to form a complete, digitally programmable, high frequency synthesizer capable of generating a frequency-agile analog output sinusoidal waveform at up to 160 MHz. The AD9954 enables fast frequency hopping coupled with fine tuning of both frequency (0.01 Hz or better) and phase (0.022° granularity).The AD9954 is programmed via a high speed serial I/O port. The device includes static RAM to support flexible frequency sweep capability in several modes, plus a user-defined linear sweep mode of operation. Also included is an on-chip high speed comparator for applications requiring a square wave output. An on-chip oscillator and PLL circuitry provide users with multiple approaches to generate the device’s system clock.The AD9954 is specified to operate over the extended industrial temperature range.Applications Agile LO frequency synthesis Programmable clock generators FM chirp source for radar and scanning systems Automotive radars Test and measurement equipment Acousto-optic device drivers

The AD9957 functions as a universal I/Q modulator and agileupconverter for communications systems where cost, size, powerconsumption, and dynamic performance are critical. TheAD9957 integrates a high speed, direct digital synthesizer(DDS), a high performance, high speed, 14-bit digital-to-analogconverter (DAC), clock multiplier circuitry, digital filters, andother DSP functions onto a single chip. It provides basebandupconversion for data transmission in a wired or wirelesscommunications system.The AD9957 is the third offering in a family of quadraturedigital upconverters (QDUCs) that includes the AD9857 andAD9856. It offers performance gains in operating speed, powerconsumption, and spectral performance. Unlike its predecessors,it supports a 16-bit serial input mode for I/Q baseband data.The device can alternatively be programmed to operate either asa single tone, sinusoidal source or as an interpolating DAC.The reference clock input circuitry includes a crystal oscillator,a high speed, divide-by-two input, and a low noise PLL formultiplication of the reference clock frequency.The user interface to the control functions includes a serial porteasily configured to interface to the SPORT of the Blackfin®DSP and profile pins to enable fast and easy shift keying of anysignal parameter (phase, frequency, or amplitude).Applications HFC data, telephony, and video modems Wireless base station transmissions Broadband communications transmissions Internet telephony

The ADA4004-1/ADA4004-2/ADA4004-4 are 1.8 nV/√Hz precision amplifiers featuring 40 μV offset, 0.7 μV/°C drift, 12 MHz bandwidth, and low 1.7 mA per amplifier supply current.The ADA4004-1/ADA4004-2/ADA4004-4 are designed on the high performance iPolar™ process, enabling improvements such as reduced noise and power consumption, increased speed and stability, and smaller footprint size. Novel design techniques enable the ADA4004-1/ADA4004-2/ADA4004-4 to achieve 1.8 nV/√Hz voltage noise density and a low 6 Hz 1/f noise corner frequency while consuming just 1.7 mA per amplifier. The small package saves board space, reduces cost, and improves layout flexibility.Applications for these amplifiers include high precision controls, PLL filters, high performance precision filters, medical and analytical instrumentation, precision power supply controls, ATE, and data acquisition systems. Operation is fully specified from ±5 V to ±15 V from −40°C to +125°C.The ADA4004-1, ADA4004-2, and ADA4004-4 are members of a growing series of low noise op amps offered by Analog Devices, Inc. (see Table 1).ApplicationsPrecision instrumentationFilter blocksMicrophone preamplifiersIndustrial controlThermocouples and RTDsReference buffers

The ADA4899-1 is an ultralow noise (1 nV/√Hz) and distortion (<−117 dBc @1 MHz) unity-gain stable voltage feedback op amp, the combination of which makes it ideal for 16-bit and 18-bit systems. The ADA4899-1 features a linear, low noise input stage and internal compensation that achieves high slew rates and low noise even at unity gain. The Analog Devices, Inc. proprietary next-generation XFCB process and innovative circuit design enable such high performance amplifiers.The ADA4899-1 drives 100 Ω loads at breakthrough performance levels with only 15 mA of supply current. With the wide supply voltage range (4.5 V to 12 V), low offset voltage (230 μV maxi-mum), wide bandwidth (600 MHz), and slew rate (310 V/μs), the ADA4899-1 is designed to work in the most demanding applications. The ADA4899-1 also features an input bias current cancellation mode that reduces input bias current by a factor of 60.The ADA4899-1 is available in a 3 mm × 3 mm LFCSP and an 8-lead SOIC package. Both packages feature an exposed metal paddle that improves heat transfer to the ground plane, which is a significant improvement over traditional plastic packages. The ADA4899-1 is rated to work over the extended industrial temperature range, −40°C to +125°C.Applications Analog-to-digital drivers Instrumentation Filters IF and baseband amplifiers DAC buffers Optical electronics

The ADCMP604 / ADCMP605 are very fast comparators fabricated on the Analog Devices, Inc. proprietary XFCB2 process. These comparators are exceptionally versatile and easy to use. Features include an input range from VEE − 0.5 V to VCCI + 0.2 V, low noise, LVDS-compatible output drivers, and TTL/CMOS latch inputs with adjustable hysteresis and/or shut-down inputs.The devices offer 1.5 ns propagation delays with 1 ps rms random jitter (RJ). Overdrive and slew rate dispersion are typically less than 50 ps.A flexible power supply scheme allows the devices to operate with a single 2.5 V positive supply and a −0.5 V to +2.7 V input signal range up to a 5.5 V positive supply with a −0.5 V to +5.7 V input signal range. Split input/output supplies, with no sequencing restrictions on the ADCMP605, support a wide input signal range with greatly reduced power consumption.The LVDS-compatible output stage is designed to drive any standard LVDS input. The comparator input stage offers robust protection against large input overdrive, and the outputs do not phase reverse when the valid input signal range is exceeded. High speed latch and programmable hysteresis features are also provided in a unique single-pin control option.The ADCMP604 is available in a 6-lead SC70 package, and the ADCMP605 is available in a 12-lead LFCSP.APPLICATIONS High speed instrumentation Clock and data signal restoration Logic level shifting or translation Pulse spectroscopy High speed line receivers Threshold detection Peak and zero-crossing detectors High speed trigger circuitry Pulse-width modulators Current-/voltage-controlled oscillators Automatic test equipment (ATE)

The ADF4154 is a fractional-N frequency synthesizer that implements local oscillators in the up conversion and down conversion sections of wireless receivers and transmitters. It consists of a low noise digital phase frequency detector (PFD), a precision charge pump, and a programmable reference divider. There is a Σ-Δ based fractional interpolator to allow programmable fractional-N division. The INT, FRAC, and MOD registersdefine an overall N divider (N = (INT + (FRAC/MOD))). In addition, the 4-bit reference counter (R counter) allows selectable REFIN frequencies at the PFD input. A complete phase-locked loop (PLL) can be implemented if the synthesizer is used with an external loop filter and a voltage controlled oscillator (VCO).A key feature of the ADF4154 is the fast-lock mode with a builtintimer. The user can program a predetermined count-down time value so that the PLL will remain in wide bandwidth mode, instead of having to control this time externally.Control of all on-chip registers is via a simple 3-wire interface. The device operates with a power supply ranging from 2.7 V to 3.3 V, and can be powered down when not in use.

The ADF4212L is a dual frequency synthesizer that can be usedto implement local oscillators (LO) in the up-conversion and down-conversion sections of wireless receivers and transmitters. It can provide the LO for both the RF and IF sections. It consists of a low noise digital phase frequency detector (PFD), a precision charge pump, a programmable reference divider, programmable A and B counters, and a dual modulus prescaler (P/P + 1). The A (6-bit) and B (12-bit) counters, in conjunction with the dual modulus prescaler (P/P + 1), implement an Ndivider (N = BP + A). In addition, the 15-bit reference counter(R Counter), allows selectable REFIN frequencies at the PFDinput. A complete phase-locked loop (PLL) can be implemented if the synthesizer is used with external loop filters and voltage controlled oscillators (VCOs).Control of all the on-chip registers is via a simple 3-wire interface with 1.8 V compatibility. The devices operate with a power supply ranging from 2.7 V to 3.3 V and can be powered down when not in use.Applications Wireless handsets (GSM, PCS, DCS, DSC1800, CDMA, WCDMA) Base stations for wireless Radio (GSM, PCS, DCS, CDMA, WCDMA) Wireless LANS Cable TV tuners (CATV) Communications test equipment

The ADG1208 and ADG1209 are monolithic, iCMOS® analogmultiplexers comprising eight single channels and four differentialchannels, respectively. The ADG1208 switches one of eight inputsto a common output as determined by the 3-bit binary addresslines A0, A1, and A2. The ADG1209 switches one of fourdifferential inputs to a common differential output as determinedby the 2-bit binary address lines A0 and A1. An EN input onboth devices enable or disable the device. When disabled, allchannels are switched off. When on, each channel conductsequally well in both directions and has an input signal rangethat extends to the supplies.The iCMOS (industrial CMOS) modular manufacturingprocess combines high voltage CMOS (complementary metal-oxidesemiconductor) and bipolar technologies. It enables thedevelopment of a wide range of high performance analog ICscapable of 33 V operation in a footprint that no other generationof high voltage devices has been able to achieve. Unlike analogICs using conventional CMOS processes, iCMOS componentscan tolerate high supply voltages while providing increasedperformance, dramatically lower power consumption, andreduced package size.The ultralow capacitance and exceptionally low charge injectionof these multiplexers make them ideal solutions for data acquisitionand sample-and-hold applications, where low glitch and fastsettling are required. There is minimum chargeinjection over the entire signal range of the device. iCMOSconstruction also ensures ultralow power dissipation, making theds ideally suited for portable and battery-powered instruments.Applications Audio and video routing Automatic test equipment Data-acquisition systems Battery-powered systems Sample-and-hold systems Communication systems