Single/Dual, +15 V/5 V, 256-Position, I2C-Compatible Digital Potentiometer Features: AD5280: 1 channel AD5282: 2 channels 256 positions +10 V to +15 V single supply; ±5.5 V dual-supply operation 20 kΩ, 50 kΩ, 200 kΩ fixed terminal resistance Low temperature coefficient: 30 ppm/°C Power-on midscale preset1  Programmable reset Operating temperature: −40°C to +85°C I2C-compatible interface

Dual 600 MHz, 50 mW Current Feedback Amplifier Features: Excellent video specifications (RL = 150 Ω, G = +2) Gain flatness: 0.1 dB to 60 MHz Differential gain error: 0.01% Differential phase error: 0.02° Low power Maximum power supply current (50 mW): 5.0 mA/amp High speed and fast settling −3 dB bandwidth (G = +1): 600 MHz −3 dB bandwidth (G = +2): 500 MHz Slew rate: 1200 V/μs Settling time to 0.1%: 16 ns Low distortion THD at fC = 5 MHz: −65 dBc Third-order intercept at f1 = 10 MHz: 33 dBm SFDR at f = 5 MHz: −66 dB Crosstalk at f = 5 MHz: −60 dB High output drive Over 70 mA output current Drives up to eight back terminated 75 Ω loads (four loads/side) while maintaining good differential gain/phase performance (0.01%/0.17°) Available in 8-lead SOIC and MSOP packages

Low Cost, High Speed Rail-to-Rail Amplifier (Dual) Features:Low cost single (AD8091) and dual (AD8092) amplifiers Fully specified at +3 V, +5 V, and 5 V supplies Single-supply operation Output swings to within 25 mV of either rail High speed and fast settling on 5 V110 MHz, 3 dB bandwidth (G = +1)145 V/s slew rate50 ns settling time to 0.1% Good video specifications (G = +2)Gain flatness of 0.1 dB to 20 MHz; RL = 150 0.03% differential gain error; RL = 1 k0.03%differential phase error; RL = 1 kLow distortion 80 dBc total harmonic @ 1 MHz; RL = 100 Outstanding load drive capabilityDrives 45 mA, 0.5 V from supply railsDrives 50 pF capacitive load (G = +1) Low power of 4.4 mA per amplifier

Very High Common-Mode Voltage Precision Difference Amplifier Features: ±600 V common-mode voltage range Rail-to-rail output Fixed gain of 1 Wide power supply range of ±2.5 V to ±18 V 550 μA typical power supply current Excellent ac specifications 90 dB minimum CMRR 310 kHz bandwidth High accuracy dc performance ±5 ppm maximum gain nonlinearity ±10 µV/°C maximum offset voltage drift ±5 ppm/°C maximum gain drift Download AD8479-EP data sheet (pdf) Military temperature range (−55°C to +125°C) Controlled manufacturing baseline One assembly/test site One fabrication site Product change notification Qualification data available on request A62/19619 VID DSCC Drawing Number

Single-Supply, Low Cost Instrumentation Amplifier Features:Gain set with 1 resistor per amplifierGain = 5 to 1000InputsVoltage range to 150 mV below negative rail25 nA maximum input bias current30 nV/Hz, RTI noise @ 1 kHzPower suppliesDual supply: 2V to 12Single supply: 3V to 24V500 A maximum supply current

Single-Supply, Low Cost Instrumentation Amplifier Features:Gain set with 1 resistor per amplifierGain = 5 to 1000InputsVoltage range to 150 mV below negative rail25 nA maximum input bias current30 nV/Hz, RTI noise @ 1 kHzPower suppliesDual supply: 2V to 12Single supply: 3V to 24V500 A maximum supply current

DC-to-2.5 GHz High IP3 Active Mixer Features: High-performance active mixer Broadband operation to 2.5 GHz Conversion gain: 7 dB Input IP3: 16.5 dBm LO drive: –10 dBm Noise figure: 14 dB Input P1dB: 2.8 dBm See datasheet for additional features

50 MHz to 1000 MHz Quadrature Demodulator Features: 50 MHz – 1000 MHz RF input range Integrated 45 dB linear-in-dB VGA IF amplifier Integrated baseband output amplifiers Demodulation bandwidth 75 MHz Quadrature phase accuracy 0.5° Amplitude balance 0.25 dB Third order intercept IIP3 +28 dBm (min gain) Noise figure 11 dB (max gain) Low LO drive –10 dBm Single supply 2.7 V to 5.5 V with power down

STEPPER MOTOR, 2-PH, 0.67A, 12N-CM; Coil Type:Bipolar; Torque Max:12N-cm; Current Rating:670mA; No. of Phases:Two Phase; Resistance:9.2ohm; Inductance:7.2mH; Inertia:18g-cm²; Product Range:PANdrive Series; SVHC:No SVHC (27-Jun-2018)

Supervisory Circuits Watchdog Supervisor with MR. IC.