The ADM101E is a single channel RS-232 driver and receiver inthe Analog Devices Craft Port series, designed to operate from asingle, 5 V supply. A highly efficient charge-pump voltage invertergenerates an on-chip –5 V supply, which eliminates the needfor a negative power supply for the driver and permits RS-232compatible output levels to be developed using charge pumpcapacitors as small as 0.1 μF.A shutdown input disables the charge pump and puts the deviceinto a low power shutdown mode, in which the current consumptionis typically less than 1 μA. The transmitter is disabledduring shutdown but the receiver remains functional. Craft Port is a trademark of Analog Devices, Inc.An epitaxial BiCMOS construction minimizes power consumptionto 3 mW and also guards against latch-up. Overvoltageprotection is provided allowing the receiver inputs to withstandcontinuous voltages in excess of ±30 V. In addition, all I-O pinshave ESD protection to levels greater than 15 kV.The ADM101E is available in a 10-lead μSOIC package, whichmakes it ideal for serial communications in small, portableapplications such as palmtop computers and mobile telephones,where a full, RS-232 serial interface is not required, but compactsize and low power drain are paramount.

The ADM101E is a single channel RS-232 driver and receiver inthe Analog Devices Craft Port series, designed to operate from asingle, 5 V supply. A highly efficient charge-pump voltage invertergenerates an on-chip –5 V supply, which eliminates the needfor a negative power supply for the driver and permits RS-232compatible output levels to be developed using charge pumpcapacitors as small as 0.1 μF.A shutdown input disables the charge pump and puts the deviceinto a low power shutdown mode, in which the current consumptionis typically less than 1 μA. The transmitter is disabledduring shutdown but the receiver remains functional. Craft Port is a trademark of Analog Devices, Inc.An epitaxial BiCMOS construction minimizes power consumptionto 3 mW and also guards against latch-up. Overvoltageprotection is provided allowing the receiver inputs to withstandcontinuous voltages in excess of ±30 V. In addition, all I-O pinshave ESD protection to levels greater than 15 kV.The ADM101E is available in a 10-lead μSOIC package, whichmakes it ideal for serial communications in small, portableapplications such as palmtop computers and mobile telephones,where a full, RS-232 serial interface is not required, but compactsize and low power drain are paramount.

The OP282/OP482 dual and quad operational amplifiers feature excellent speed at exceptionally low supply currents. Slew rate exceeds 7 V/µs with supply current under 250 µA per amplifier. these unity gain stable amplifiers have a typical gain bandwidth of 4 MHz.The JFET input stage of the OP282/OP482 insures bias current is typically a few piocamps and below 500 pA over the full temperature range. Offset voltage is under 3 mV for the dual and under 4 mV for the quad.With a wide output swing, within 1.5 volts of each supply, low power consumption and high slew rate, the OP282/OP482 are ideal for battery-powered systems or power restricted applications. An input common-mode range that includes the positive supply makes the OP282/OP482 an excellent choice for high-side signal conditioning.The Op282/OP482 are specified over the extended industrial temperature range. Both dual and quad amplifiers are available in plastic and ceramic DIP plus SOIC surface mount packages.

The OP777, OP727 and OP747 are precision single, dual and quad rail-to-rail output single supply amplifiers featuring micropower operationand rail to rail output ranges. These amplifiers provide improved performance over the industry standard OP07 with ±15V supplies and offer the further advantages of true single supply operationdown to +3.0V and smaller package options than any other high voltage precision bipolar amplifier. Outputs are stable with capacitive loads of over1000pF. Supply current is less than 300 µA per amplifier at 5V. 500 series resistors protect the inputs, allowing input signal levels several voltsabove the positive supply without phase reversal.

The AD8138 is a major advancement over op amps fordifferential signal processing. The AD8138 can be used as asingle-ended-to-differential amplifier or as a differential-to-differentialamplifier. The AD8138 is as easy to use as an opamp and greatly simplifies differential signal amplification anddriving. Manufactured on the proprietary ADI XFCB bipolarprocess, the AD8138 has a −3 dB bandwidth of 320 MHz anddelivers a differential signal with the lowest harmonic distortionavailable in a differential amplifier. The AD8138 has a uniqueinternal feedback feature that provides balanced output gainand phase matching, suppressing even order harmonics. Theinternal feedback circuit also minimizes any gain error thatwould be associated with the mismatches in the external gainsetting resistors.The differential output of the AD8138 helps balance the inputto differential ADCs, maximizing the performance of the ADC. The AD8138 eliminates the need for a transformer with highperformance ADCs, preserving the low frequency and dc information.The common-mode level of the differential output isadjustable by a voltage on the VOCM pin, easily level-shifting theinput signals for driving single-supply ADCs. Fast overloadrecovery preserves sampling accuracy. The AD8138 distortion performance makes it an ideal ADCdriver for communication systems, with distortion performancegood enough to drive state-of-the-art 10-bit to 16-bit convertersat high frequencies. The high bandwidth and IP3 of theAD8138 also make it appropriate for use as a gain block in IFand baseband signal chains. The AD8138 offset and dynamicperformance makes it well suited for a wide variety of signalprocessing and data acquisition applications. The AD8138 is available in both SOIC and MSOP packages foroperation over −40°C to +85°C temperatures.The AD8138-EP supports defense and aerospace applications (AQEC).

The AD8220 is the first single-supply, JFET input instrumentation amplifier available in an MSOP package. Designed to meet the needs of high performance, portable instrumentation, the AD8220 has a minimum common-mode rejection ratio (CMRR) of 86 dB at dc and a minimum CMRR of 80 dB at 5 kHz for G = 1. Maximum input bias current is 10 pA and typically remains below 300 pA over the entire industrial temperature range. Despite the JFET inputs, the AD8220 typically has a noise corner of only 10 Hz.With the proliferation of mixed-signal processing, the number of power supplies required in each system has grown. The AD8220 is designed to alleviate this problem. The AD8220 can operate on a ±18 V dual supply, as well as on a single +5 V supply. Its rail-to-rail output stage maximizes dynamic range on the low voltage supplies common in portable applications. Its ability to run on a single 5 V supply eliminates the need to use higher voltage, dual supplies. The AD8220 draws a maximum of 750 μA of quiescent current, making it ideal for battery powered devices.Gain is set from 1 to 1000 with a single resistor. Increasing the gain increases the common-mode rejection. Measurements that need higher CMRR when reading small signals benefit when the AD8220 is set for large gains.A reference pin allows the user to offset the output voltage. This feature is useful when interfacing with analog-to-digital converters. The AD8220 is available in an MSOP that takes roughly half the board area of an SOIC. Performance for the A and B grade is specified over the industrial temperature range of −40°C to +85°C, and the W grade is specified over the automotive temperature range of −40°C to +125°C.Applications Medical instrumentation Precision data acquisition Transducer interfaces

The AD8220 is the first single-supply, JFET input instrumentation amplifier available in an MSOP package. Designed to meet the needs of high performance, portable instrumentation, the AD8220 has a minimum common-mode rejection ratio (CMRR) of 86 dB at dc and a minimum CMRR of 80 dB at 5 kHz for G = 1. Maximum input bias current is 10 pA and typically remains below 300 pA over the entire industrial temperature range. Despite the JFET inputs, the AD8220 typically has a noise corner of only 10 Hz.With the proliferation of mixed-signal processing, the number of power supplies required in each system has grown. The AD8220 is designed to alleviate this problem. The AD8220 can operate on a ±18 V dual supply, as well as on a single +5 V supply. Its rail-to-rail output stage maximizes dynamic range on the low voltage supplies common in portable applications. Its ability to run on a single 5 V supply eliminates the need to use higher voltage, dual supplies. The AD8220 draws a maximum of 750 μA of quiescent current, making it ideal for battery powered devices.Gain is set from 1 to 1000 with a single resistor. Increasing the gain increases the common-mode rejection. Measurements that need higher CMRR when reading small signals benefit when the AD8220 is set for large gains.A reference pin allows the user to offset the output voltage. This feature is useful when interfacing with analog-to-digital converters. The AD8220 is available in an MSOP that takes roughly half the board area of an SOIC. Performance for the A and B grade is specified over the industrial temperature range of −40°C to +85°C, and the W grade is specified over the automotive temperature range of −40°C to +125°C.Applications Medical instrumentation Precision data acquisition Transducer interfaces

The AD8541/AD8542/AD8544 are single, dual, and quad rail-to-rail input and output single-supply amplifiers featuring very low supply current and 1 MHz bandwidth. All are guaranteed to operate from a 2.7 V single supply as well as a 5 V supply. These parts provide 1 MHz bandwidth at a low current consumption of 45 μA per amplifier.Very low input bias currents enable the AD8541/AD8542/AD8544 to be used for integrators, photodiode amplifiers, piezoelectric sensors, and other applications with high source impedance. The supply current is only 45 μA per amplifier, ideal for battery operation.Rail-to-rail inputs and outputs are useful to designers buffering ASICs in single-supply systems. The AD8541/AD8542/AD8544 are optimized to maintain high gains at lower supply voltages, making them useful for active filters and gain stages.The AD8541/AD8542/AD8544 are specified over the extended industrial temperature range (–40°C to +125°C). The AD8541 is available in 8-lead SOIC, 5-lead SC70, and 5-lead SOT-23 packages. The AD8542 is available in 8-lead SOIC, 8-lead MSOP, and 8-lead TSSOP surface-mount packages. The AD8544 is available in 14-lead narrow SOIC and 14-lead TSSOP surface-mount packages. All MSOP, SC70, and SOT versions are available in tape and reel only.ApplicationsASIC input or output amplifiers Sensor interfaces Piezoelectric transducer amplifiers Medical instrumentations Mobile communications Audio outputs Portable systems Data Sheet, Rev. F, 1/08

The AD8646 and the AD8647 are the dual, and the AD8648 isthe quad, rail-to-rail, input and output, single-supply amplifiersfeaturing low offset voltage, wide signal bandwidth, low inputvoltage, and low current noise. The AD8647 also has a lowpower shutdown function.The combination of 24 MHz bandwidth, low offset, low noise,and very low input bias current makes these amplifiers useful ina wide variety of applications. Filters, integrators, photodiodeamplifiers, and high impedance sensors all benefit from thecombination of performance features. AC applications benefitfrom the wide bandwidth and low distortion. The AD8646/AD8647/AD8648 offer high output drive capability, which isexcellent for audio line drivers and other low impedanceapplications. The AD8646 and AD8648 are available forautomotive applications (see the Ordering Guide).Applications include portable and low powered instrumentation,audio amplification for portable devices, portable phoneheadsets, barcode scanners, and multipole filters. The ability toswing rail to rail at both the input and output enables designersto buffer CMOS ADCs, DACs, ASICs, and other wide outputswing devices in single-supply systems.Applications Battery-powered instruments Multipole filters ADC front ends Sensors Barcode scanners ASIC input or output amplifiers Audio amplifiers Photodiode amplifiers Datapath/mux/switch control

The ADM705 / ADM706 / ADM707 / ADM708 microprocessorsupervisory circuits are suitable for monitoring 5 V powersupplies/batteries and microprocessor activity.The ADM705 / ADM706 provide power-supply monitoringcircuitry that generate a reset output during power-up, powerdown,and brownout conditions. The reset output remainsoperational with VCC as low as 1 V. Independent watchdogmonitoring circuitry is also provided. This is activated if thewatchdog input has not been toggled within 1.60 sec.In addition, there is a 1.25 V threshold detector to warn ofpower failures, to detect low battery conditions, or to monitor anadditional power supply. An active low, debounced manual resetinput (MR) is also included.The ADM705 and ADM706 are identical except for the resetthreshold monitor levels, which are 4.65 V and 4.40 V, respectively.The ADM707 and ADM708 provide a similar functionality tothe ADM705 and ADM706 and only differ in that a watchdogtimer function is not available. Instead, an active high resetoutput (RESET) is available as well as the active low reset output(RESET). The ADM707 and ADM708 are identical except forthe reset threshold monitor levels, which are 4.65 V and 4.40 V,respectively.All devices are available in narrow 8-lead PDIP and 8-lead SOICpackages.APPLICATIONS Microprocessor systems Computers Controllers Intelligent instruments Critical microprocessor supply monitoring