24-bit, 2 Channel Capacitance to Digital Converter Features:New standard in single chip solutions Interfaces to single or differential floating sensors Resolution down to 4 aF (that is, up to 21 ENOB) Accuracy: 4 fF Linearity: 0.01% Common-mode (not changing) capacitance up to 17 pF Full-scale (changing) capacitance range: 4 pF Tolerant of parasitic capacitance to ground up to 60 pF Update rate: 10 Hz to 90 Hz Simultaneous 50 Hz and 60 Hz rejection at 16 Hz Temperature sensor on-chip Resolution: 0.1C, accuracy: 2C Voltage input channel Internal clock oscillator 2-wire serial interface (I2C-compatible) Power 2.7 V to 5.25 V single-supply operation 0.7 mA current consumption Operating temperature: 40C to +125C 16-lead TSSOP package

14-Bit, 250 kSPS PulSAR, Pseudo Differential ADC in MSOP/LFCSP Features: 14-bit resolution with no missing codes Throughput: 250 kSPS INL: ±0.4 LSB typical, ±1 LSB maximum (±0.0061% of FSR) SINAD: 85 dB @ 20 kHz THD: −100 dB @ 20 kHz Pseudo differential analog input range 0 V to VREF with VREF up to VDD No pipeline delay See Data Sheet for Additional Information

18-Bit, 15 MSPS, Module Data Acquisition Solution Features: Integrated fully differential ADC driver with signal scaling Wide input common-mode voltage range High common-mode rejection Single-ended to differential conversion Pin selectable input range with overrange Input ranges with 4.096 V REFBUF: ±10 V, ±5 V, ±4.096 V, ±2.5 V, and ±1.5 V Gain/attenuation options: 0.37, 0.73, 0.87, 1.38, and 2.25 Critical passive components 0.005% precision matched resistor array for FDA 9 mm × 9 mm, 0.8 mm pitch, 100-ball CSP_BGA package 2.5× footprint reduction vs. discrete solution Low power, dynamic power scaling, power-down mode 143 mW typical at 15 MSPS Throughput: 15 MSPS, no pipeline delay INL error: ±3.1 ppm typical, ±6.2 ppm maximum (Gain = 0.73, gain = 0.87, gain = 1.38, gain = 2.25) SINAD: 90.4 dB typical at 20 kHz (gain = 0.73) THD: −117 dB at 1 kHz, −110 dB at 100 kHz (gain = 0.73) Gain error: ±0.005%FS typical Gain error drift: ±0.13 ppm/°C typical On-board reference buffer with VCMO generation Serial LVDS interface Wide operating temperature range: −40°C to +85°C

Dual Channel, Configurable, IsolatedDigital Input Features: Dual channel, configurable, isolated digital input Programmable trip threshold On-chip debounce filter On-chip data and power Isolation Application circuit monitors wide voltage range 10 V dc to 300 V dc 8 V rms to 240 V rms ac (with 10 ms + pickup) Negative dc protected Programmable wetting current Pulse up to 50 mA Constant current up to 6.3 mA Safety and regulatory approvals UL recognition 3750 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A (pending) CSA 61010-1: 300 V rms VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-1 VIORM = 565 V peak EMC robust solution supports relay protection system level requirements ADC samples available for system diagnostics Internal SAR ADC with PGA Single 3.3 V Supply Integrated isoPower, isolated dc-to-dc converter Interfaces SPI DOUTx output reflects state of digital input IRQ interrupt pin Operating temperature: −40°C to +125°C 20-lead, LGA package with 6.8 mm creepage

High Performance Polyphase Energy Measurement IC Features: 7 high performance analog-to-digital converters (ADCs) 101 dB signal-to-noise ratio (SNR) 10,000:1 dynamic range Wide input range: ±1 V, 0.707 V rms full scale Differential inputs ±25 ppm/°C maximum channel temperature drift (including ADC, internal VREF, and PGA drift) enabling Class 0.2 meters with standard external components Power quality measurements Line frequency: 1 measurement per phase Zero crossing detection, zero-crossing timeout Phase angle measurements Supports current transformers (CTs) and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 64 points per line cycle for ease of external harmonic analysis Events can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total active power, volt-amperes reactive (VAR), volt-amperes (VA), watthour, VAR-hour, and VA-hour Fundamental VAR and VAR-hour Current and voltage rms per phase (xIRMS, xVRMS) Supports active energy standards: IEC 62053-21, IEC 62053-22; EN50470-3; OIML R46, ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-4 High speed communication port 10 MHz serial peripheral interface (SPI)

Single 12-/10-/8-Bit I2C VOUT DACs with 10ppm/C Reference Features: Integrated Precision Reference 2.5V Full-Scale 10ppm/°C (LTC2631-L) 4.096V Full-Scale 10ppm/°C (LTC2631-H) Maximum INL Error: 1LSB (LTC2631A-12) Bidirectional Reference: Input or 10ppm/°C Output 400kHz I2C Interface Nine Selectable Addresses (LTC2631-Z) Low Noise (0.7mVP-P , 0.1Hz to 200kHz) Guaranteed Monotonic Over Temperature 2.7V to 5.5V Supply Range (LTC2631-L) Low Power Operation: 180μA at 3V Power Down to 1.8μA Maximum (C and I Grades) Power-On Reset to Zero or Mid-Scale Options Double-Buffered Data Latches Guaranteed Operation From –40°C to 125°C (H-Grade) 8-Lead TSOT-23 (ThinSOT™) Package

12-Bit, 105Msps Ultralow Power 1.8V ADCs Features: 70.8dB SNR 85dB SFDR Low Power: 124mW/103mW/87mW Single 1.8V Supply CMOS, DDR CMOS or DDR LVDS Outputs Selectable Input Ranges: 1VP-P to 2VP-P 800MHz Full-Power Bandwidth S/H Optional Data Output Randomizer Optional Clock Duty Cycle Stabilizer Shutdown and Nap Modes Serial SPI Port for Configuration Pin Compatible 14-Bit and 12-Bit Versions 40-Pin (6mm × 6mm) QFN Package

Differential Ultra-Tiny, 16-Bit I2C ADCs with 10ppm/C Max Precision Reference Features: 16-Bit Resolution, No Missing Codes Internal Reference, High Accuracy 10ppm/°C (Max) Single-Ended (LTC2461) or Differential (LTC2463) 2LSB Offset Error (Typ) 0.01% Gain Error (Typ) 60 Conversions Per Second Single Conversion Settling Time for Multiplexed Applications 1.5mA Supply Current 200nA Sleep Current Internal Oscillator—No External Components Required 2-Wire I2C Interface with Two Addresses Plus One Global Address for Synchronization Ultra-Tiny, 12-Lead, 3mm × 3mm DFN and MSOP Packages

Octal 12-/10-/8-Bit I2C VOUT DACs with 10ppm/C Reference Features: Integrated Precision Reference: 2.5V Full-Scale 10ppm/°C (LTC2637-L) 4.096V Full-Scale 10ppm/°C (LTC2637-H) Maximum INL Error: 2.5LSB (LTC2637-12) Low Noise: 0.75mVP-P 0.1Hz to 200KHz Guaranteed Monotonic Over –40°C to 125°C Temperature Range Selectable Internal or External Reference 2.7V to 5.5V Supply Range (LTC2637-L) Ultralow Crosstalk Between DACs (<3nV•s) Low Power: 100μA per DAC at 3V (LTC2637-L) Power-On-Reset to Zero-Scale/Mid-Scale Double-Buffered Data Latches Tiny 14-Lead 4mm × 3mm DFN and 16-Lead MSOP Packages

Quad 16-/12-Bit Rail-to-Rail DACs with 10ppm/C Max Reference Features: Precision Reference 10ppm/°C Max Maximum INL Error: ±4LSB at 16-Bits Low ±2mV (Max) Offset Error Guaranteed Monotonic Over Temperature Selectable Internal or External Reference 2.7V to 5.5V Supply Range (LTC2654-L) Integrated Reference Buffers Ultralow Crosstalk Between DACs (<3nV•s) Power-on-Reset to Zero-Scale/Mid-Scale Asynchronous DAC Update Pin Tiny 20-Lead 4mm × 4mm QFN and 16-Lead Narrow SSOP Packages