The LTC3225/LTC3225-1 are programmable supercapacitor chargers designed to charge two supercapacitors in series to a selectable fixed output voltage (4.8V/5.3V for the LTC3225 and 4V/4.5V for the LTC3225-1) from input supplies as low as 2.8V to 5.5V. Automatic cell balancing prevents overvoltage damage to either supercapacitor. No balancing resistors are required. Low input noise, low quiescent current and low external parts count (one flying capacitor, one bypass capacitor at VIN and one programming resistor) make the LTC3225/LTC3225-1 ideally suited for small battery-powered applications. Charge current level is programmed with an external resistor. When the input supply is removed, the LTC3225/LTC3225-1 automatically enter a low current state, drawing less than 1?A from the supercapacitors. The LTC3225/LTC3225-1 are available in a 10-lead 2mm ? 3mm DFN package.Applications Current Limited Applications with High Peak Power Loads (LED Flash, PCMCIA Tx Bursts, HDD Bursts, GPRS/GSM Transmitter) Backup Supplies

The ADP5070 is a dual high performance dc-to-dc regulator that generates independently regulated positive and negative rails.The input voltage range of 2.85 V to 15 V supports a wide variety of applications. The integrated main switch in both regulators enables generation of an adjustable positive output voltage up to +39 V and a negative output voltage down to ?39 V below input voltage.The ADP5070 operates at a pin selected 1.2 MHz/2.4 MHz switching frequency. The ADP5070 can synchronize with an external oscillator from 1.0 MHz to 2.6 MHz to ease noise filtering in sensitive applications. Both regulators implement programmable slew rate control circuitry for the MOSFET driver stage to reduce electromagnetic interference (EMI).Flexible start-up sequencing is provided with the options of manual enable, simultaneous mode, positive supply first, and negative supply first.The ADP5070 includes a fixed internal or resistor programmable soft start timer to prevent inrush current at power-up. During shutdown, both regulators completely disconnect the loads from the input supply to provide a true shutdown.Other key safety features in the ADP5070 include overcurrent protection (OCP), overvoltage protection (OVP), thermal shutdown (TSD), and input undervoltage lockout (UVLO).The ADP5070 is available in a 20-lead LFCSP or in a 20-lead TSSOP and is rated for a ?40?C to +125?C junction temperature range.Applications Bipolar amplifiers, ADCs, DACs and multiplexers Charge-coupled device (CCD) bias supply Optical module supply RF power amplifier (PA) bias

Power Management IC Development Tools LTC4121EUD Demo Board - 400mA Synchronou

3A, 4MHz, Monolithic Synchronous Step-Down Regulator Features: High Efficiency: Up to 95% 3A Output Current Low Quiescent Current: 64μA Low RDS(ON) Internal Switch: 77mΩ 2.25V to 5.5V Input Voltage Range Programmable Frequency: 300kHz to 4MHz ±2% Output Voltage Accuracy 0.8V Reference Allows Low Output Voltage Selectable Forced Continuous/Burst Mode® Operation with Adjustable Burst Clamp Synchronizable Switching Frequency Low Dropout Operation: 100% Duty Cycle Power Good Output Voltage Monitor Overtemperature Protected Available in 16-Lead Exposed Pad TSSOP and QFN Packages

Power Management IC Development Tools LT3669 Demo Board 7.5V to 40V input with Vout 1 being 5V at 100mA and Vout 2 (LDO) being 3.3V at 100mA

The LTM8047 is an isolated flyback ?Module DC/DC converter. The LTM8047 has an isolation rating of 725VDC. For a similar product with LDO post regulator, see the LTM8048. Included in the package are the switching controller, power switches, transformer, and all support components. Operating over an input voltage range of 3.1V to 32V, the LTM8047 supports an output voltage range of 2.5V to 12V, set by a single resistor. Only output, input, and bypass capacitors are needed to finish the design. Other components may be used to control the soft-start control and biasing.The LTM8047 is packaged in a thermally enhanced, compact (11.25mm ? 9mm ? 4.92mm) over-molded ball grid array (BGA) package suitable for automated assembly by standard surface mount equipment. The LTM8047 is available with SnPb (BGA) or RoHS compliant terminal finish.Applications Industrial Sensors Industrial Switches Ground Loop Mitigation

Standalone Linear Li-Ion Battery Charger with Micropower Comparator Features: Charge Current Programmable up to 1A Charges Single Cell Li-Ion Batteries Directly from USB Port Preset Float Voltage with ±0.35% Accuracy Micropower Comparator for Battery Monitoring Thermal Regulation Maximizes Charge Rate Without Risk of Overheating Programmable Charge Current Detection/Termination Programmable Charge Termination Timer Smart Pulsing Error Feature SmartStart™ Prolongs Battery Life 20µA Charger Quiescent Current in Shutdown Available in a Low Profile (0.75mm) 10-Lead (3mm × 3mm) DFN Package

2ALowVin VeryLow DO low noise high PSSR / REEL7

3ALowVin VeryLow DO low noise high PSSR / REEL7

3.3/5Vin 2A Ultra Low Noise LDO Fixed