The analog output ADXL356 and the digital output ADXL357 are low noise density, low 0 g offset drift, low power, 3-axis accelerometers with selectable measurement ranges. The ADXL356B supports the ±10 g and ±20 g ranges, the ADXL356C supports the ±10 g and ±40 g ranges, and the ADXL357 supports the ±10 g, ±20 g, and ±40 g ranges.The ADXL356/ADXL357 offer industry leading noise, minimal offset drift over temperature, and long-term stability, enabling precision applications with minimal calibration.The low drift, low noise, and low power ADXL357 enables accurate tilt measurement in an environment with high vibration. The low noise of the ADXL356 over higherfrequencies is ideal for condition-based monitoring and other vibration sensing applications.The ADXL357 multifunction pin names may be referenced only by their relevant function for either the serial peripheral interface (SPI) or limited I2C interface.Applications Inertial measurement units (IMUs)/altitude and heading reference systems (AHRSs) Platform stabilization systems Structural health monitoring Seismic imaging Tilt sensing Robotics Condition monitoring

The ADXRS645 is a high performance angular rate sensor with excellent vibration immunity for use in high temperature environments. The ADXRS645 is manufactured using the Analog Devices, Inc., patented high volume BiMOS surface-micromachining process with years of proven field reliability. An advanced, differential, quad sensor design provides superior acceleration and vibration rejection.The output signal, RATEOUT, is a voltage proportional to the angular rate about the axis normal to the package lid. The measurement range is a minimum of ±2000°/sec, and may be extended to ±5000°/sec with the addition of a single external resistor. The output is ratiometric with respect to a provided reference supply. Other external capacitors are required for operation.A temperature output is provided for compensation techniques. Two digital self-test inputs electromechanically excite the sensor to test proper operation of both the sensor and the signal conditioning circuits. The ADXRS645 is available in a 8 mm × 9 mm × 3 mm, 15-lead brazed lead tri in-line package.APPLICATIONS Down hole measurements for geological exploration Extreme high temperature industrial applications Severe mechanical environments

The ADIS16495 is a complete inertial system that includes a triaxis gyroscope and a triaxis accelerometer. Each inertial sensor in the ADIS16495 combines industry leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements.The ADIS16495 provides a simple, cost effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The serial peripheral interface (SPI) and register structure provide a simple interface for data collection and configuration control.The footprint and connector system of the ADIS16495 enable a simple upgrade from the ADIS16375, ADIS16480, ADIS16485, ADIS16488A, and ADIS16490. The ADIS16495 is available in an aluminum package that is approximately 47 mm × 44 mm × 14 mm and includes a standard connector interface.Applications Precision instrumentation, stabilization Guidance, navigation, control Avionics, unmanned vehicles Precision autonomous machines, robotics

The ADIS16137 iSensor® is a high performance, digital gyroscope sensing system that operates autonomously and requiresno user configuration to produce accurate rate sensing data. Itprovides performance advantages with its low noise density,wide bandwidth, and excellent in-run bias stability, which enableapplications such as platform control, navigation, robotics, andmedical instrumentation.This sensor system combines industry leading iMEMS® technologywith signal conditioning that optimizes dynamic performance.The factory calibration characterizes the entire sensor signal chainfor sensitivity and bias over a temperature range of −40°C to +85°C.As a result, each ADIS16137 has its own unique correctionformulas to produce accurate measurements upon installation.For some systems, the factory calibration eliminates the needfor system level calibration and greatly simplifies it for others.The ADIS16137 provides data at rates of up to 2048 SPS andoffers an averaging/decimation filter structure for optimizing noise/bandwidth trade-offs. The serial peripheral interface (SPI) anduser register structure provide easy access to configuration controlsand calibrated sensor data for embedded processor platforms.The 36 mm × 44 mm × 14 mm package provides four holes forsimple mechanical attachment, using M2 (or 2-56 standard size)machine screws along with a standard 24-lead, dual row, 1 mmpitch connector that supports electrical attachment to a printedcircuit board (PCB) or cable system. It is package and pincompatible with the ADIS16133, ADIS16135 and ADIS16136.APPLICATIONS Precision instrumentation Platform stabilization and controls Industrial vehicle navigation Downhole instrumentation Robotics

The ADXL362 is an ultralow power, 3-axis MEMS accelerometer that consumes less than 2 μA at a 100 Hz output data rate and 270 nA when in motion triggered wake-up mode. Unlike accelerometers that use power duty cycling to achieve low power consumption, the ADXL362 does not alias input signals by undersampling; it samples the full bandwidth of the sensor at all data rates.The ADXL362 always provides 12-bit output resolution; 8-bit formatted data is also provided for more efficient single-byte transfers when a lower resolution is sufficient. Measurement ranges of ±2 g, ±4 g, and ±8 g are available, with a resolution of 1 mg/LSB on the ±2 g range. For applications where a noise level lower than the normal 550 μg/√Hz of the ADXL362 is desired, either of two lower noise modes (down to 175 μg/√Hz typical) can be selected at minimal increase in supply current.In addition to its ultralow power consumption, the ADXL362 has many features to enable true system level power reduction. It includes a deep multimode output FIFO, a built-in micropower temperature sensor, and several activity detection modes including adjustable threshold sleep and wake-up operation that can run as low as 270 nA at a 6 Hz (approximate) measurement rate. A pin output is provided to directly control an external switch when activity is detected, if desired. In addition, the ADXL362 has provisions for external control of sampling time and/or an external clock.The ADXL362 operates on a wide 1.6 V to 3.5 V supply range, and can interface, if necessary, to a host operating on a separate, lower supply voltage. The ADXL362 is available in a 3 mm × 3.25 mm × 1.06 mm package.APPLICATIONS Hearing aids Home healthcare devices Motion enabled power save switches Wireless sensors Motion enabled metering devices

Temperature Sensor: 10-Bit Digital in 6-Lead SOT-23 Features: 10-Bit Temperature-to-Digital Converter –40°C to +125°C Operating Temperature Range ±2°C Accuracy SPI-and DSP-Compatible Serial Interface Shutdown Mode Space-Saving SOT-23 Package

Integrated Optical Module with Ambient Light Rejection and Two LEDs Features: 3.8 mm × 5.0 mm × 0.9 mm module with integrated optical components 2 green LEDs, 2 PDs with IR cut filter 2 external sensor inputs 3, 370 mA LED drivers 20-bit burst accumulator enabling 20 bits per sample period On-board sample to sample accumulator enabling up to 27 bits per data read Custom optical package made to work under a glass window Optimized SNR for signal limited cases I2C or SPI communications

Low Noise, Wide Bandwidth, MEMS Accelerometer Features: Single, in plane axis accelerometer with analog output Full-scale range: ±100 g Linear frequency response range: dc to 23 kHz typical (3 dB point) Resonant frequency: 42 kHz typical Ultralow noise density: 75 μg/√Hz Overrange sensing plus dc coupling allows fast recovery time Complete electromechanical self test Single-supply operation Output voltage ratiometric to supply Low power consumption: 1.0 mA typical Power saving standby operation mode with fast recovery RoHS compliant −40°C to +125°C operating temperature range 32-lead, 5 mm × 5 mm × 1.80 mm LFCSP package See datasheet for additional features

200 g Range, 3-Axis Digital Accelerometer Features: ±200 g measurement range Low power: 170 μA in measurement mode and 17 μA in standby mode at VS = 2.5 V (typical) User selectable bandwidth up to 3200 Hz ODR Fixed 13-bit output resolution Supply voltage range: 2.0 V to 3.6 V Embedded memory management system with FIFO technology minimizes host processor load Shock event detection Activity/inactivity monitoring SPI (3- or 4-wire) and I2C digital interfaces Wide temperature range: −40 to +125°C 10,000 g shock survival Pb free and RoHS compliant Small and thin: 32-lead, 5 mm × 5 mm × 1.45 mm LFCSP AEC-Q100 qualified for automotive applications

3-Axis, 2 g/4 g/8 g/16 g Ultralow Power Digital Accelerometer Features: Multipurpose accelerometer with 10- to 13-bit resolution for use in a wide variety of applications Digital output accessible via SPI (3- and 4-wire) and I2C Built-in motion detection features make tap, double-tap, activity, inactivity, orientation, and free-fall detection trivial user-adjustable thresholds interrupts independently mappable to two interrupt pins Low power operation down to 23 μA and embedded FIFO for reducing overall system power Wide supply and I/O voltage range: 1.7 V to 2.75 V Wide operating temperature range (−40°C to +85°C) 10,000 g shock survival Small, thin Pb free, RoHS compliant 3 mm × 3 mm × 0.95 mm LGA package