Microprocessor Supervisory in SOT-23 with Active High and Low Push-Pull Output Features: Reliable Low Cost Voltage Monitor with Reset Output Suitable for Monitoring 2.5 V, 3 V, 3.3 V, and 5 V Power Supply Voltages Reset Threshold Levels: 4.62 V, 4.35 V, 3.06 V, 2.88 V, 2.55 V, 2.31 V, and 2.18 V (Typ)Initialize Microprocessor Systems with Added Safety Open-Drain Output Choices (ADM1811, ADM1813, ADM1816, and ADM1818) Can Be Used with a Manual Push-Button to Generate a Reset (ADM1813, ADM1818) Available in 3-Lead SOT-23 and SC70 Packages Active High and Low Push-Pull Output Choices (ADM1810, ADM1812, ADM1815, and ADM1817)

High Speed, 5 V, 0.1 F CMOS RS-232 Driver/Receiver Features: 120 kB transmission rate Small (0.1 µF) charge pump capacitors Single 5 V power supply Meets TIA/EIA-232-E and V.28 specifications 2 drivers and 2 receivers On-board dc-to-dc converters ±9 V output swing with 5 V supply Low power BiCMOS: 2.5 mA ICC ±30 V receiver input levels

Micropower 3-Sensor Combination Including Acceleration and Temperature Features: All sensors sampled synchronously Up to 400 Hz ODR Samples can be synchronized to external trigger Ultralow power 1.95 A at 100 Hz ODR, 2.0 V supply, all sensors on 270 nA at 6 Hz motion activated wake-up mode 10 nA standby current 12-bit resolution for all sensors Acceleration scale factor down to 1 mg/LSB Temperature scale factor: 0.065C/LSB (typical) Built-in features for motion-based system level power savings Adjustable threshold sleep/wake modes for motion activation Accelerometer, temperature sensor, and provision for third analog sensor input Autonomous interrupt processing, without need for microcontroller intervention, to allow the rest of the system to be turned off completely Deep embedded FIFO minimizes host processor load Awake state output enables implementation of standalone, motion activated switch Wide supply and I/O voltage ranges: 1.6 V to 3.5 VOperates off 1.8 V to 3.3 V railsPower can be derived from coin cell batterySPI digital interfaceSmall and thin 3 mm 3.25 mm 1.06 mm package

12-Bit High Speed Multiplying D/A Converter Features: Differential Nonlinearity: ±1/2 LSB Nonlinearity: 0.05% Fast Settling Time: 250 ns High Compliance: -5 V to +10 V Differential Outputs: 0 to 4 mA Guaranteed Monotonicity: 12 bits Low Full-Scale Tempco: 10 ppm/°C Circuit Interface to TTL, CMOS, ECL, PMOS/NMOS Low Power Consumption: 225 mW Industry Standard AM6012 Pinout Available in Die Form

Quad 8-Bit Multiplying CMOS D/A Converter with Memory Features: Four DACs in a 28 Pin, 0.6 Inch Wide DIP or 28-Pin JEDEC Plastic Chip Carrier ±1/4 LSB Endpoint Linearity Guaranteed Monotonic DACs Matched to Within 1% Microprocessor Compatible Read/Write Capability (with Memory) TTL/CMOS Compatible Four-Quadrant Multiplication Single-Supply Operation (+5 V) Low Power Consumption Latch-Up Resistant Available in Die Form

13 Gbps, Fast Rise Time AND/NAND/OR/NOR Gate, with Programmable Output Voltage Features: Supports High Data Rates: up to 13 Gbps Differential & Single-Ended Ouputs Fast Rise & Fall Times: 19 / 18 ps Low Power Consumption: 230 mW typ. Single Supply: -3.3V Programmable Differential Output Voltage Swing: 600 - 1100 mV Propagation Delay: 95 ps 16 Lead Ceramic 3 × 3mm SMT Package: 9mm2;

Digital Isolators THREE-CHANNEL DIGITAL ISOLATORS

Quad-Channel Digital Isolator Features: Low power operation 5 V operation (see data sheet) 3 V operation (see data sheet) Bidirectional communication 3 V/5 V level translation High data rate: dc to 90 Mbps (NRZ) Precise timing characteristics 2 ns maximum pulse width distortion 2 ns maximum channel-to-channel matching See data sheet for additional features

Equalisers Front Panel HDMI Buffer - TMDS Only

Operational Amplifiers - Op Amps VLTG-FDBK, G= 2 CLAMP AMP