32 Gbps Limiting Amplifier SMT Features: Supports Data Rates up to 43 Gbps Low Power Dissipation: 300 mW @ VCC = +3.3V Differential Small Signal Gain: 30 dB High Input Sensitivity: 10 mVP-P Differential 3-dB Bandwidth: 26.5 GHz Adjustable Output Voltage Swing up to 800 mVP-P Differential 16 Lead 3x3mm SMT package: 9mm2

20 Gbps Clocked Comparator with RSPECL Output Stage Features: Propagation Delay Clock to Output: 120 ps Overdrive & Slew Rate Dispersion: 10 ps Minimum Pulse Width: 60 ps Resistor Programmable Hysteresis Differential Clock Control Input Bandwidth: 10 GHz Power Dissipation: 150 mW RSCML & RSECL Versions Available 16 Lead 3×3mm SMT Package: 9mm2

9 GHz to 12 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 11 dB (typical) at IFOUT = 100 MHz Image rejection: 25 dB (typical) at IFOUT = 100 MHz LO to RF isolation: 46 dB (typical) LO to IF isolation: 26 dB (typical) IF output frequency: dc to 3.5 GHz 32-lead, 4.9 mm × 4.9 mm ceramic leadless chip carrier

5.6 GHz to 8.6 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 13 dB typical Image rejection: 32 dBc typical Input P1dB compression: −6 dBm typical Input IP3: 3 dBm typical, 6.0 GHz to 8.6 GHz Noise figure: 2 dB typical LO to RF isolation: 48 dBm typical LO to IF isolation: 13 dBm typical RF to IF isolation: 10 dBm typical Amplitude balance: 0.2 dB typical Phase balance: −2° typical RF return loss: 10 dB typical LO return loss: 15 dB typical IF return loss: 15 dB typical Exposed paddle, 4 mm × 4 mm, 24-lead, LFCSP

5.6 GHz to 8.6 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 13 dB typical Image rejection: 32 dBc typical Input P1dB compression: −6 dBm typical Input IP3: 3 dBm typical, 6.0 GHz to 8.6 GHz Noise figure: 2 dB typical LO to RF isolation: 48 dBm typical LO to IF isolation: 13 dBm typical RF to IF isolation: 10 dBm typical Amplitude balance: 0.2 dB typical Phase balance: −2° typical RF return loss: 10 dB typical LO return loss: 15 dB typical IF return loss: 15 dB typical Exposed paddle, 4 mm × 4 mm, 24-lead, LFCSP

Aerospace Monolithic JFET Input Operational Amplifier Features:Low Input Bias and Offset Currents Low Input Offset Voltage: 1.0mV typical Low Input Offset Voltage Drift: 3.0V/C typical Low Input Noise Current High Common-Mode Rejection Ratio: 100dB Low Supply Current

Quad Voltage Monitor and Sequencer Features: Powered from 2.7 V to 5.5 V on the VCC pin Logical core with internal timeouts provides power supply sequencing and fault protection 4 inputs can be programmed to monitor different voltage levels with resistor dividers Monitors 4 supplies via 0.8% accurate comparators 3 open-drain enable outputs Open-drain power-good output (PWRGD) 10-lead MSOP

Digital Power Monitor with PMBus Interface Features: Monitor current and two voltages High accuracy current monitoring at low sense voltage 0.33% accurate at ±20 mV sense voltage over temperature Support high side and low side current sensing Integrated shunt regulator for wide supply input Reports current, voltage and power Power accumulation for energy metering Bidirectional current sensing Digital programmable over current alert See datasheet for additional features

3 kV RMS Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 3 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y and Z pins ≥±12 kV IEC61000-4-2 contact discharge ≥±15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2565E/ADM2567E) Low speed 500 kbps data rate for EMI control (ADM2561E/ADM2563E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/µs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 196 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

3 kV RMS Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 3 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y and Z pins ≥±12 kV IEC61000-4-2 contact discharge ≥±15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2565E/ADM2567E) Low speed 500 kbps data rate for EMI control (ADM2561E/ADM2563E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/µs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 196 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance