Single-Phase Active and Apparent Energy Metering IC Features: High accuracy; supports IEC 61036/60687, IEC62053-21, and IEC62053-22 On-chip digital integrator enables direct interface-to-current sensors with di/dt output A PGA in the current channel allows direct interface to shunts and current transformers Active and apparent energy, sampled waveform, and current and voltage rms Less than 0.1% error in active energy measurement over a dynamic range of 1000 to 1 at 25°C Positive-only energy accumulation mode available On-chip user programmable threshold for line voltage surge and SAG and PSU supervisory Digital calibration for power, phase, and input offset On-chip temperature sensor (±3°C typical) SPI®-compatible serial interface Please see data sheet for additional features.

High Performance Narrowband ISM Transceiver IC Features: Low power, high performance, narrowband transciever Frequency Bands: 80-650MHz and 862-940MHz Modulation schemes: 2FSK, 3FSK, 4FSK Spectral shaping: Gaussian and Raised Cosine Filtering Automatic PA ramp Data rates supported: 0.05kps to 25kbps Programmable output power: –16dBm to +13dBm Low IF architecture with programmable IF bandwidths of 12.5/18.5/25kHz 2.3V to 3.6V Power Supply Receiver sensitivity: –123dBm @ 1kbps FSK Fully automatic frequency control loop (AFC) compensates for lower tolerance crystals High Accuracy digital RSSI and integrated Tx/Rx switch

CMOS, 2.5 Low Voltage Quad SPDT Switch Features: 1.8 V to 5.5 V Single Supply ±2.5 V Dual Supply 2.5 Ω On Resistance 0.5 Ω On Resistance Flatness 100 pA Leakage Currents Triple SPDT: ADG786 Quad SPDT: ADG788 19 ns Switching Times 20-Lead 4 mm × 4 mm Chip Scale Packages Low Power Consumption TTL/CMOS-Compatible Inputs For Functionally-Equivalent Devices in 16-Lead TSSOP Packages, See ADG733/ADG734 Qualified for automotive applications

Wideband, 43 dB Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, 2:1 Mux/SPDT Switches Features: Wideband switch: −3 dB at 4 GHz Absorptive/reflective switches High off isolation (43 dB at 1 GHz) Low insertion loss (0.8 dB at 1 GHz) Single 1.65 V to 2.75 V power supply CMOS/LVTTL control logic 8-lead MSOP and tiny 3 mm × 3 mm LFCSP Low power consumption (<1 µA)

5.7 kV RMS 500kbps Full Duplex Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 5.7 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y, and Z pins 12 kV IEC61000-4-2 contact discharge 15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2865E/ADM2867E) Low speed 500 kbps data rate for EMI control (ADM2861E/ADM2863E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/μs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 192 bus nodes (72 k receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

5.7 kV RMS/1.5 kV RMS, Quad-Channel LVDS 2.5 Gigabit Isolator (0 Reverse Channels) Features: 5.7 kV rms and 1.5 kV rms LVDS isolators Complies with TIA/EIA-644-A LVDS signal levels Quad-channel configuration Any data rate up to 2.5 Gbps switching with low jitter 10 Gbps total bandwidth across four channels 2.15 ns typical propagation delay Typical jitter: 0.82 ps rms random, 40 ps total peak Lower power 1.8 V supplies ±8 kV IEC 61000-4-2 ESD protection across isolation barrier High common-mode transient immunity: 100 kV/μs typical Safety and regulatory approvals (28-lead SOIC_W_FP package) UL (pending): 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 VPEAK (working voltage) Enable or disable refresh (low speed output correctness check) Operating temperature range: −40°C to +125°C 28-lead, wide-body, finer pitch SOIC_W_FP package with 8.3 mm creepage and clearance or 6 mm × 6 mm LFCSP package with 1.27 mm creepage and clearance

3.3 V, 200 Mbps, Full-Duplex, High Speed M-LVDS Transceiver Features: Full Duplex M-LVDS transceiver (driver and receiver pair) Switching rate: 200 Mbps (100 MHz) Type 1 receiver with hysteresis of 25 mV Compatible with the TIA/EIA-899 standard for M-LVDS Glitch free power-up/power-down on M-LVDS bus Controlled transition times on driver output Common-mode range: −1 V to +3.4 V, allowing communication with 2 V of ground noise Driver outputs high-Z when disabled or powered off Enhanced ESD protection on bus pins ≥±15 kV HBM, air discharge ≥±8 kV HBM, contact discharge ≥±10 kV IEC 61000-4-2, air discharge ≥±8 kV IEC 61000-4-2, contact discharge Operating junction temperature range: −40°C to +120°C 16-lead, 4 mm x 4 mm LFCSP package

Small, 3.75 kV RMS Quad Digital Isolators (2/2 Channel Directionality) Features: Up to 25 Mbps data rate (NRZ) Low propagation delay: 25 ns typical Low dynamic power consumption 1.8 V to 5 V level translation High temperature operation: 125°C High common-mode transient immunity: >25 kV/µs Output default select 20-lead, RoHS-compliant, SSOP package Safety and regulatory approvals: UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 560 V peak

12 Bit Digital to Analog Converter 1 16-PDIP

Digital to Analog Converters - DAC Q08L 12-BIT VOLTAGE OUT DAC I.C.