High Current Hot Swap Controller with I2C Compatible Monitoring Features: Allows Safe Board Insertion Into Live Backplane 12-/16-Bit ADC with ±0.9% Total Unadjusted Error Monitors Current, Voltage, Power and Energy Controls Two Parallel N-Channel MOSFETs for SOA Sharing in High Current Applications Internal EEPROM for Nonvolatile Configuration Wide Operating Voltage Range: 2.9V to 33V I2C/SMBus Digital Interface (Coexists with PMBus Devices) 12V Gate Drive for Lower MOSFET RDS(ON) Programmable Current Limit with 2% Accuracy MOSFET Power Limiting with Current Foldback Continuously Monitors MOSFET Health Stores Minimum and Maximum Measurements Alerts When Alarm Thresholds Exceeded Input Overvoltage and Undervoltage Protection Internal ±5% or External Timebases 32-Pin 5mm × 5mm QFN Package AEC-Q100 Qualified for Automotive Applications

8-Channel PMBus Power System Manager Featuring Accurate Output Voltage Measurement Features: Sequence, Trim, Margin and Supervise Eight Power Supplies Manage Faults, Monitor Telemetry and Create Fault Logs PMBus™ Compliant Command Set Supported by LTpowerPlay® GUI Margin or Trim Supplies to Within 0.25% of Target Fast OV/UV Supervisors Per Channel Coordinate Sequencing and Fault Management Across Multiple LTC PSM Devices Automatic Fault Logging to Internal EEPROM Operate Autonomously without Additional Software Internal Temperature and Input Voltage Supervisors Accurate Monitoring of Eight Output Voltages, Input Voltage and Internal Die Temperature I2C/SMBus Serial Interface Can Be Powered from 3.3V, or 4.5V to 15V Programmable Watchdog Timer 100% Pin-Compatible Upgrade to the LTC2978/LTC2978A Available in 64-Pin 9mm × 9mm QFN PackageAEC-Q100 Qualified for Automotive Applications

35V/3.2A Multi-Cell Lithium-Ion Step-Down Battery Charger with PowerPath and I2C Telemetry Features: Li-Ion/Polymer Battery Charger with Termination Wide Charging Input Voltage Range: 4.5V to 35V High Efficiency Synchronous Operation 16-Bit Digital Telemetry System Monitors VBAT, IBAT, RBAT, TBAT, TDIE, VIN, IIN, VOUT Charges 1-8 Lithium-Ion/Polymer Cells Input Undervoltage Charge Current Limit Loop Input MPPT for Solar Panel Inputs Input Current Limit Prioritizes System Load Output Low Loss PowerPath™ Instant-On Operation with Discharged or Missing Battery JEITA Temperature Controlled Charging Pin Compatible with LiFePO4 and SLA Versions

55V Buck-Boost Multi-Chemistry Battery Charger Features: Wide Voltage Range: 4.5V to 55V Input, Up to 55V Output (60V Absolute Maximums) Synchronous Buck-Boost DC/DC Controller Li-Ion and Lead-Acid Charge Algorithms ±0.5% Float Voltage Accuracy ±5% Charge Current Accuracy Instant-On for Heavily Discharged Batteries Ideal Diode Controller Provides Low Loss PowerPath When Input Power is Limited Input Voltage Regulation for High Impedance Input Supplies and Solar Panel Peak Power Operation Onboard Timer for Protection and Termination Bad Battery Detection with Auto-Reset NTC Input for Temperature Qualified Charging Binary Coded Open-Collector Status Pins Low Profile (0.75mm) 38-Pin 5mm × 7mm QFN Package

Nanopower Buck-Boost DC/DC with Energy Harvesting Battery Life Extender Features: Dual Input, Single Output DC/DCs with Input Prioritizer Energy Harvesting Input: 3.0V to 19V Buck DC/DC Primary Cell Input: 1.8V to 5.5V Buck-Boost DC/DC Zero Battery IQ When Energy Harvesting Source is Available Ultralow Quiescent Current: 750nA at No-Load Low Noise LDO Post Regulator Integrated Supercapacitor Balancer Up to 50mA of Output Current Programmable DC/DC and LDO Output Voltages, Buck UVLO, and Buck-Boost Peak Input Current Integrated Low Loss Full-Wave Bridge Rectifier Input Protective Shunt: Up to 25mA at VIN ≥ 20V 5mm × 5mm QFN-32 Package

Active Clamp Synchronous Forward Controller Features: Input Voltage Range: 8.5V to 100V Programmable Volt-Second Clamp High Efficiency Control: Active Clamp, Synchronous Rectification, Programmable Delays Short-Circuit (Hiccup Mode) Overcurrent Protection Programmable Soft-Start/Stop Programmable OVLO and UVLO with Hysteresis Programmable Frequency (100kHz to 500kHz) Synchronizable to an External Clock

Fixed Frequency SOT-23 Oscillator Features: No External Components to Set Frequency Frequency Error ±0.5% Typical Fast Start-Up Time: 100µs Typical ±20ppm/°C Temperature Stability Includes Output Enable Includes Divide by 1, 2 or 4 Rise Time: 0.5ns, CL = 5pF Timing Jitter: <0.8% Typical Duty Cycle: 50% ±2.5% IS = 8mA Typical (fOSC = 100MHz, CL = 5pF) CMOS Output Drives 600Ω Load Single Supply 2.7V to 5.5V Low Profile (1mm) ThinSOT™ Package

16-/14-/11-Bit 2.5Gsps DACs Features:80dBc SFDR at 70MHz fOUT>68dBc SFDR from DC to 1000MHz fOUT40mA Nominal Full-Scale, ±1V Output Compliant10mA to 60mA Adjustable Full-Scale Current RangeSingle or Dual Port DDR LVDS and DHSTL InterfaceLow Latency (7.5 Cycles for Single Port, 11 Cycles for Dual Port)>78dBc 2-Tone IMD from DC to 1000MHz fOUT–165dBc/Hz Additive Phase Noise at 1MHz Offset for 65MHz fOUT170-Lead (9mm × 15mm) BGA Package

Backup Battery Controller with Fixed Output Features: Not Recommended For New Designs. Contact Analog Devices for Potential Replacement. Complete Battery Backup System in an SO-8, 16-Pin GN or SO Package Generates Fixed Backup Voltage (3.07V/4.63V) from a Single 1.2V NiCd Button Cell Automatic Main Supply to Backup Switching Minimum 100mW Output Power Automatic Fast Recharge of NiCd Battery Programmable NiCd Trickle Charge Current Smart NiCd Charger Minimizes Recharge Time and Maximizes System Efficiency After Backup Onboard Power-Up and Push-Button Reset Generator Performs VCC Supervisory Functions Reset Assertion Guaranteed at VCC = 1V Short-Circuit Protection Thermal Limiting

High Efficiency Bidirectional Multicell Battery Balancer Features: Bidirectional Synchronous Flyback Balancing of Up to 6 Li-Ion or LiFePO4 Cells in Series Up to 10A Balancing Current (Set by Externals) Integrates Seamlessly with the LTC680x Family of Multicell Battery Stack Monitors Bidirectional Architecture Minimizes Balancing Time and Power Dissipation Up to 92% Charge Transfer Efficiency Stackable Architecture Enables >1000V Systems Uses Simple 2-Winding Transformers 1MHz Daisy-Chainable Serial Interface with 4-Bit CRC Packet Error Checking High Noise Margin Serial Communication Numerous Fault Protection Features 48-Lead Exposed Pad QFN and LQFP Packages AEC-Q100 Qualified for Automotive Applications