High Performance, Multiphase Energy, and Power Quality Measurement IC Features: 7 high performance ADCs 101 dB SNR Wide input voltage range: ±1 V, 707 mV rms FS at gain = 1 Differential inputs ±25 ppm/°C maximum channel drift (including ADC, internal VREF, PGA drift) enabling 10000:1 dynamic input range Class 0.2 metrology with standard external components Power quality measurements Enables implementation of IEC 61000-4-30 Class S VRMS ½, IRMS ½ rms voltage refreshed each half cycle 10 cycle rms/12 cycle rms Dip and swell monitors Line frequency—one per phase Zero crossing, zero-crossing timeout Phase angle measurements Supports CTs and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 128 points per line cycle for ease of external harmonic analysis Events, such as dip and swell, can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total and fundamental active power, volt amperes reactive (VAR), volt amperes (VA), watthour, VAR hour, and VA hour Total and fundamental IRMS, VRMS Total harmonic distortion Power factor Supports active energy standards: IEC 62053-21 and IEC 62053-22; EN50470-3; OIML R46; and ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-24 High speed communication port: 20 MHz serial port interface (SPI) Integrated temperature sensor with 12-bit successive approximation register (SAR) ADC ±3°C accuracy from −40°C to +85°C

Energy Metering IC with Autocalibration Features: mSure autocalibration Automatic calibration based on a direct measurement of the full signal path Calibration procedure not requiring a reference meter mSure autocalibration Class 1 meter guaranteed 3 high performance ADCs 88 dB SNR High gain current channel: ±26.04 mV peak, 18.4 mV rms input at highest gain setting Advanced metrology feature set WATT, VAR, VA, Wh, VARh, and VAh Supports active energy standards: IEC 62053-21; IEC 62053-22; EN50470-3; OIML R46; and ANSI C12.20 Supports reactive energy standards: IEC 62053-23 and IEC 62053-24 Current and voltage rms measurement Power quality measurements Operating temperature, industrial range: −40°C to +85°C

9.85 GHz to 20.5 GHz, Wideband, MMIC VCO Features: Wide output frequency range: 9.85 GHz to 20.5 GHz Wide tuning bandwidth Low single sideband phase noise: −83 dBc/Hz at 100 kHz offset No external resonator needed Supply current: 70 mA typical at VCC = 5 V 24-terminal, 3.90 mm × 3.90 mm, ceramic LCC package

Configurable Impedance Network Analyzer & Potentiostat with Integrated Cortex M3 Core Features: Analog performance 160 kSPS, 16-bit, precision analog-to-digital converter (ADC) 4 dedicated voltage measurement channels 8 current measurement channels Impedance measurement engine High precision voltage reference Supply noise rejection filtering Ultralow leakage configurable switch matrix 12-bit digital-to-analog converter (DAC) Precision instrumentation amplifier control loop 6-channel CapTouch controller Temperature sensor Analog hardware accelerators Autonomous analog front-end (AFE) controller Independent sequencer for AFE functions Direct digital synthesizer (DDS)/arbitrary waveform generator Receive filters Complex impedance measurement (DFT) engine Processing 16 MHz ARM Cortex-M3 processor 384 kB of embedded flash memory 32 kB system SRAM 16 kB Flash configured EEPROM Integrated full-speed USB 2.0 controller and PHY Multilayer advanced microcontroller bus architecture (AMBA) bus matrix Central direct memory access (DMA) controller Real-time clock (RTC) General-purpose, wake-up, and watchdog timers Communication Input/output I2S and beeper interface LCD display controller (parallel and serial) LCD segment controller SPI, I2C, and UART peripheral interfaces Programmable GPIOs Power Coin cell battery compatible 2.5 V to 3.6 V active measurement range Power management unit (PMU) Power-on reset (POR) and power supply monitor (PSM) Packages and temperature range Operating temperature range: −40°C to +85°C Package: 120-lead, 8 mm × 8 mm CSP_BGA 

16-Bit, Isolated Sigma-Delta Modulator Features: 5 MHz to 21 MHz master clock input frequency Offset drift vs. temperature: ±0.6 μV/°C maximum SNR: 86 dB typical 16 bits, no missing codes Full-scale analog input voltage range: ±320 mV ENOB: 14 bits typical IDD1: 10 mA maximum On-board digital isolator Operating temperature range: −40°C to +125°C High common-mode transient immunity: 150 kV/μs minimum, VDD2 = 3.3 V Wide-body SOICs 16-lead SOIC_W 8-lead SOIC_IC with increased creepage Safety and regulatory approvals (pending) UL recognition 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice SA VOE Certificate of Conformity DIN V VDE V 0884-10 VlORM = 1270 VPEAK DIN V VDE V 0884-11 VlORM = 1060 VPEAK

16-Bit, Isolated, Sigma-Delta ADC Features: 5 MHz to 21 MHz master clock input frequency Offset drift vs. temperature: ±0.6 μV/°C maximum SNR: 86 dB typical 16 bits, no missing codes Full-scale analog input voltage range: ±320 mV ENOB: 14 bits typical IDD1: 10 mA maximum On-board digital isolator Operating temperature range −40°C to +125°C (16-lead SOIC_W) −40°C to +105°C (8-lead SOIC_IC) 20 V operation on VDD1 High CMTI: 150 kV/μs minimum, VDD2 = 3.3 V Wide-body SOICs 16-lead SOIC_W 8-lead SOIC_IC with increased creepage Safety and regulatory approvals UL recognition 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (Pending) VDE Certificate of Conformity DIN V VDE V 0884-10: VIORM = 1270 VPEAK DIN V VDE V 0884-11: VIORM = 1060 VPEAK (Pending)

67 dB SMT SDLVA, 0.5 - 18.5 GHz Features: High Logging Range: 67 dB (-62 to +5 dBm) Output Frequency Flatness: ±2 dB Log Linearity: ±2 dB Fast Rise/Fall Times: 5/15 ns Single Positive Supply: +3.3V ESD Sensitivity (HBM): Class 1A 24 Lead 4x4mm SMT Package: 16mm2

GaAs MMIC SPDT Switch SMT, DC - 3 GHz Features: Low Insertion Loss: 0.4dB Ultra Small Package: MSOP8 High Input IP3: +50 dBm Positive Control: 0/+3V @ 0.1 uA

High Voltage, Latch-Up Proof, 16-Channel Multiplexer Features: Latch-up proof 3.5 pF off source capacitance 64 pF off drain capacitance 0.35 pC typical charge injection ±0.02 nA on channel leakage Low on resistance: 155 typical ±9 V to ±22 V dual-supply operation 9 V to 40 V single-supply operation VSS to VDD analog signal range Human body model (HBM) ESD rating - 8 kV all other pins

Dual Channel, 16-Bit, 16 MUPS, Multispan, Multi-IO SPI DAC Features: 16-bit resolution 16 MUPS single channel rate in fast mode 11 MUPS single channel rate in precision mode 78 ns small signal settling time to 0.1% accuracy 100 ns large signal settling time to 0.1% accuracy Ultrasmall glitch: <50 pV×s Ultralow latency: 5 ns THD: −105 dB at 1 kHz Highly configurable output voltage span and offset 1.2 V and 1.8 V logic level compatible Single (classic) and dual SPI modes Multiple error detectors, both analog and digital domains 2.5 V internal voltage reference, 10 ppm/°C maximum temperature coefficient Small package: 4 mm × 4 mm LFCSP