The ADG901/ADG902 are wideband switches that use a complementary metal-oxide semiconductor (CMOS) process to provide high isolation and low insertion loss to 1 GHz. The ADG901 is an absorptive (matched) switch with 50 ? terminated shunt legs, while the ADG902 is a reflective switch. These devices are designed such that the isolation is high over the dc to 1 GHz frequency range. These switches enable the user to pass dc signals up to 0.5 V without the use of a dc blocking capacitor. They have on-board CMOS control logic, thus eliminating the need for external controlling circuitry. The control inputs are both CMOS and LVTTL compatible. The low power consumption of these CMOS devices makes them ideally suited to wireless applications and general-purpose high frequency switching.Product Highlights 40 dB Off Isolation at 1 GHz 0.8 dB Insertion Loss at 1 GHz 17 dBm P1dB at 1 GHzApplications Wireless communications General purpose RF switching Dual-band applications High speed filter selection Digital transceiver front-end switch IF switching Tuner modules Antenna diversity switching list

SMD Data Sheet

Integrated Circuit True RMS-to-DC Converter

Dual Low Power, 8-Bit TxDAC Digital-to-Analog Converters Features:Power dissipation @ 3.3 V, 20 mA output191 mW @ 10 MSPS 232 mW @ 125 MSPSSleep mode: Supply voltage: 1.8 V to 3.3 VSFDR to Nyquist86 dBc @ 1 MHz output 85 dBc @ 10 MHz outputNSD @ 10 MHz output, 125 MSPS, 20 mA: 132 dBc/Hz Differential current outputs: 4 mA to 20 mA2 on-chip auxiliary DACsCMOS inputs with single-port operationOutput common mode: adjustable 0 V to 1.2 VSmall footprint 40-lead LFCSP RoHS-compliant package

Digitally Programmable Sensor Signal Amplifier Features: Very low offset voltage: 12 μV maximum over temperature  Very low input offset voltage drift:  65 nV/°C maximum High CMRR: 96 dB minimum  Digitally programmable gain and output offset voltage  Gain range from 28 to 1300  Single-wire serial interface  Stable with any capacitive load  SOIC and LFCSP packages  2.7 V to 5.5 V operation  Qualified for automotive applications

Hot Swap Controller and I2C Power Monitor Features: Allows safe board insertion and removal from a live backplane  Controls supply voltages from 3.15 V to 16.5 V  Precision current sense amplifier  Precision voltage input  12-bit ADC for current and voltage readback  Charge pumped gate drive for external N-channel FET  I2C fast mode-compliant interface (400 kHz maximum) Adjustable analog current limit with circuit breaker  ±3% accurate hot swap current limit level  Fast response limits peak fault current  Automatic retry or latch-off on current fault  Programmable hot swap timing via TIMER pin  Active-high ON pin  2 address pins allow 16 devices on the same bus 10-lead MSOP

DSP Microcomputer

Dual 12-Bit, LVDS Interface 500 MSPS DAC Features: High dynamic range, dual DAC parts LVDS inputs with dual-port or optional interleaved single-port operation Single carrier W-CDMA ACLR = 80 dBc @ 61.44 MHz IF Innovative switching output stage permits usable outputs beyond Nyquist frequency LVDS inputs with dual-port or optional interleaved singleport operation See datasheet for additional features

800 MHz, Linear-in-dB VGA with AGC Detector Features: Analog variable gain range: −12 dB to +22 dB Linear-in-dB scaling: 37.5 dB/V 3 dB bandwidth: 800 MHz @ VGAIN = 0.5 V Integrated rms detector P1dB: 16 dBm @ 140 MHz Output IP3: 33 dBm @ 140 MHz Noise figure at maximum gain: 9.5 dB @ 140 MHz Input and output impedances: 50 Ω Single-supply voltage from 4.5 V to 5.5 V RoHS-compliant, 24-lead LFCSP

Complete, Dual, 12-/14-/16-Bit, Serial Input, Unipolar/Bipolar, Voltage Output DACs